91388-1 Tyco Electronics, 91388-1 Datasheet

TOOL CRIMP 4.2MM PE 18-22AWG

91388-1

Manufacturer Part Number
91388-1
Description
TOOL CRIMP 4.2MM PE 18-22AWG
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ III, VAL-U-LOK™r
Type
Crimpersr
Datasheets
1.91388-1.pdf (6 pages)
2.91388-1.pdf (5 pages)

Specifications of 91388-1

Tool Type
Hand Crimper
Features
Side Entry, Ratchet
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Pro-Crimper and die
Fits Cable/wire
22-18 AWG
For Use With/related Products
Rectangular Contacts, 18-22 AWG
For Use With
A30653 - CONN TERM PIN 18-22AWG 30GOLDA30652 - CONN TERM PIN 18-22AWG TINA30651 - CONN TERM PIN 18-22AWG 30GOLDA30650 - CONN TERM PIN 18-22AWG TINA30645 - CONN TERM SOCKET 18-22AWG 30GOLDA30644 - CONN TERM SOCKET 18-22AWG TINA30643 - CONN TERM SOCKET 18-22AWG 30GOLDA30642 - CONN TERM SOCKET 18-22AWG TIN
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
A30667
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly, also available separately.
} Contact the Tooling Assistance Center or Product Information number at the bottom of this page for specific contact part
numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool
Assembly 91388--1 consists of Die Assembly
91388--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. See Figure 1.
The die assembly consists of crimping dies and a
locator assembly.
any contacts.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial”
grade hand tool and is designed primarily for field installation, repair,
maintenance work, or prototyping in industrial, commercial, or
institutional applications. Product crimped with this tool will meet the
crimp height requirement for hand tools in the appropriate 114 series
specification, but may not comply with other feature parameters of
the specification. Tyco Electronics offers a variety of tools to satisfy
your performance requirements. For additional information, contact
the Tooling Assistance Center at 1- - 800- - 722- - 1111.
Read these instructions thoroughly before crimping
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
Die Assembly
Die Assembly
Part Number
91388 2
91388--2
Locator Assy
Locator Assy
Part Number{
58516 3
58516--3
Locator Assembly
(Supplied with Die
Assembly)
Die Assembly
Front of Tool
(Locator Side)
Ratchet Adjustment Wheel
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand
Crimping Tool Assembly 91388- 1
with Die Assembly 91388- 2
Moving Jaw
Contact Family}
Contact System
4.2 mm
4.2 mm
Figure 1
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
NOTE
Wire Size,
i
22 18
22--18
AWG
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Stationary Jaw
[.059--.095]
Insulation
1.50--2.41
1.50 2.41
Diameter
Pivot Pin
Wire
Moving Handle
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Back of Tool
(Wire Side)
Instruction Sheet
408- - 8918
Stationary Handle
05 APR 10 Rev A
[.110--.130]
2.79--3.30
2.79 3.30
Length
Strip
1 of 6
LOC B

91388-1 Summary of contents

Page 1

... Contact the Tooling Assistance Center or Product Information number at the bottom of this page for specific contact part numbers. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 91388--1 consists of Die Assembly 91388--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. See Figure 1. The die assembly consists of crimping dies and a locator assembly. Read these instructions thoroughly before crimping any contacts ...

Page 2

... To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. Tyco Electronics Corporation Tool Frame Die Retaining Pins Rev A ...

Page 3

... Locator Back of Tool (Wire Side) Wire Figure 3 Tyco Electronics Corporation This tool is provided with a crimp adjustment feature. Initially, the crimp height should be verified as specified in Figure 4. Refer to Section 6, CRIMP HEIGHT INSPECTION, and Section 7, RATCHET ADJUSTMENT, to verify crimp height before using the tool to crimp desired contacts and wire sizes ...

Page 4

... COUNTERCLOCKWISE to a higher--numbered setting looser crimp is required, rotate the adjustment wheel CLOCKWISE to a lower--numbered setting. Screwdriver Ratchet Adjustment Wheel Lock- - Screw (Typ) Tyco Electronics Corporation “A” Crimp Height Dimension A Dimension A and Tolerance (+) 0.99 +0.051 22--20 [.039 +.002] 1.22 +0.051 18 [ ...

Page 5

... CUSTOMER SERVICE (38--35) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105--3608 11. REVISION SUMMARY Applied the TE logo; S Added back page, showing tooling compatible S with dies 91388--1. Tyco Electronics Corporation ...

Page 6

... Die Assembly 91388- 2 Can Be Used In the Following Tools: PRO- CRIMPER III Hand Tool 354940- 1 (Instruction Sheet 408- 9930) SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 SDE- SA Hand Tool 9- 1478240- 0 (Instruction Sheet 408- 8851) ...