90574-1 Tyco Electronics, 90574-1 Datasheet - Page 4

• Manufacturer Part Number: 90574-1
• Description: ASSY PRO-CRIMPER COMM M-N-LOCK
• Manufacturer: Tyco Electronics
• Series: Pro-Crimper™ III, Commercial MATE-N-LOK®r

Specifications of 90574-1

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Wire Size (awg): 24-18
• Product Type: Receptacle Housings
• For Use With: 61473-1 - CONN SOCKET 18-24AWG TIN CRIMP170148-1 - CONN SOCKET M-N-L 18-24AWG TINA25554 - CONN PIN 18-24AWG TIN CRIMPA25555 - CONN SOCKET 18-24AWG TIN CRIMPA25558 - CONN PIN 18-24AWG GOLD CRIMPA25559 - CONN SOCKET 18-24AWG GOLD CRIMPA1433 - CONN SOCKET 18-24AWG GOLD CRIMPA1432 - CONN PIN 18-24AWG GOLD CRIMPA1423 - CONN SOCKET 18-24AWG TIN CRIMPA1422 - CONN PIN 18-24AWG TIN CRIMP
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 18-24 AWG
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 90574-1; A25418

6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. Tyco
Electronics does not manufacture or market
crimp--height comparators. Detailed information on
obtaining and using crimp--height comparators can be
found in instruction sheet 408--7424.
Proceed as follows:
4 of 6
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil
AWG (Max)
Wire Size
Wire Size
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
NOTE
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET (Crimp Height)
ADJUSTMENT.
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
i
20
18
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
(Wire Size Marking)
Crimp Section
Crimp Section
24--20
Figure 4
18
“A”
Dimension A and
Dimension A and
[.0385 + .0020]
[.0490 + .0020]
Crimp Height
Tolerance (+)
1.245 + .051
.978 + .051
Tyco Electronics Corporation
7. RATCHET (Crimp Height) ADJUSTMENT
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Ratchet
Adjustment
Wheel
Screwdriver
Lockscrew
(Typ)
Figure 5
(Figure 5)
Rev C