63811-8700 Molex Inc, 63811-8700 Datasheet - Page 4

• Manufacturer Part Number: 63811-8700
• Description: TOOL 22-24&32-36 AWG SL CRIMP
• Manufacturer: Molex Inc
• Series: PremiumGrade™, C-Grid® SL™r

Specifications of 63811-8700

• Tool Type: Hand Crimper
• Features: Side Entry, Ratchet
• Product: Crimping, Stripping & Cutting Tools & Drills
• Fits Cable/wire: 24-22 AWG
• Crimp Size: 36AWG To 22AWG
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• For Use With/related Products: Rectangular Contacts, 22-24 AWG and 32-36 AWG
• For Use With: WM2573CT - CONN SOCKET 22-24AWG CRIMP 15AUWM2570CT - CONN SOCKET 22-24AWG CRIMP 30AUWM2569CT - CONN SOCKET 22-24AWG CRIMP TINWM2567CT - CONN PIN 22-24AWG CRIMP 30GOLDWM2564CT - CONN SOCKET 22-24AWG CRIMP GOLDWM2573TR - CONN SOCKET 22-24AWG CRIMP 15AUWM2570TR - CONN SOCKET 22-24AWG CRIMP 30AUWM2569TR - CONN SOCKET 22-24AWG CRIMP TINWM2567TR - CONN PIN 22-24AWG CRIMP 30GOLDWM2564TR - CONN SOCKET 22-24AWG CRIMP GOLDWM2570 - CONN TERM FEMALE 22-24AWG GOLDWM2567 - CONN TERM MALE 22-24AWG GOLDWM2564 - CONN TERM FEMALE 22-24AWG GOLDWM2517CT - CONN TERM MALE 22-24AWG TINWM2515CT - CONN TERM MALE 22-24AWG GOLDWM2510CT - CONN TERM FEMALE 22-24AWG TINWM2512CT - CONN TERM FEMALE 22-24AWG GOLDWM2517TR - CONN TERM MALE 22-24AWG TINWM2515TR - CONN TERM MALE 22-24AWG GOLDWM2510TR - CONN TERM FEMALE 22-24AWG TINWM2512TR - CONN TERM FEMALE 22-24AWG GOLDWM2517 - CONN TERM MALE 22-24AWG TINWM2515 - CONN TERM MALE 22-24AWG GOLDWM2573 - CONN TERM FEMALE 22-24AWG GOLDWM2569 - CONN TERM FEMALE 22-24AWG TINWM2512 - CONN TERM FEMALE 22-24AWG GOLDWM2510 - CONN TERM FEMALE 22-24AWG TIN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 063811-8700; 063811-8700-P; 0638118700; 0638118700-P; 63811-8700-P; 638118700; 638118700-P; WM9017

Hand Crimp Tool for SL™ Crimp Terminals
Doc No. ATS-638118700
Revision: A
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
8. Remove the crimped terminal from the terminal
9. Visually inspect the crimped terminal for proper
10. On some large O.D. wires, it may not be possible
Note:
A crimp height chart is provided with this manual as
Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers available, actual crimp
height measurements may very slightly. An occasional,
destructive, pull force test should be performed to check
hand tool crimp. Pull Force value Must exceed the Minimum
pull force specifications listed.
Locator Replacement
See the parts list on the last page of this document for the
proper locator order number. Follow the steps below to
replace the locator.
1. Open the crimp hand tool.
2. Squeeze gently on the lower area shown in Figure 7A
3. Lift and pull away from the hand tool. The top locator
PRE-STRIPPED
locator by pulling on the wire.
crimp location.
to insert the wire with the tool partially closed.
Those wires should be inserted with the hand tool
in the open position. Insert the wire above the
terminal in the punch and against the wire stop
then close the tool. See Figure 6.
with your thumb and index finger. The lower tabs of the
locator should disengage from the hand tool.
hooks should slip out of the top slots easily. See Figure 7A.
WIRE
TERMINAL
Release Date: 07-30-07
Revision Date: 07-30-07
Figure 5
AGAINST THE
SQUEEZE
WIRE STOP
HERE
WIRE
UNCONTROLLED COPY
WIRE
LOWER TABS
LOCATOR
TOP SLOTS OF
TOP HOOKS
HANDTOOL
TERMINAL
WIRE STOP
Figure 6
WIRE
Figure 7A
TERMINAL
SQUEEZE
HERE
WIRE STOP IS PART OF
THE LOCATOR
CENTER OF LOCATOR
DOWN POSITION
MAKE SURE
IS IN THE
Figure 7B
Page 4 of 8