YC124-JR-071K3L Yageo, YC124-JR-071K3L Datasheet - Page 7
![RES ARRAY 1.3K OHM 8TRM 4RES SMD](/photos/9/67/96702/yc124_sml.jpg)
YC124-JR-071K3L
Manufacturer Part Number
YC124-JR-071K3L
Description
RES ARRAY 1.3K OHM 8TRM 4RES SMD
Manufacturer
Yageo
Series
YC124r
Datasheet
1.YC124-JR-07330RL.pdf
(9 pages)
Specifications of YC124-JR-071K3L
Resistance (ohms)
1.3K
Number Of Resistors
4
Circuit Type
Isolated
Temperature Coefficient
±200ppm/°C
Tolerance
±5%
Power Per Element
62.5mW
Number Of Pins
8
Package / Case
0804 (2010 Metric), Convex
Size / Dimension
0.079" L x 0.039" W (2.00mm x 1.00mm)
Height
0.018" (0.45mm)
Mounting Type
Surface Mount
Operating Temperature
-55°C ~ 155°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
YC124J-1.3KTR
TESTS AND REQUIREMENTS
Short time
overload
Board Flex/
Bending
TEST
Life/
Operational Life/
Endurance
High
Temperature
Exposure/
Endurance at
upper category
temperature
Moisture
Resistance
Thermal Shock
Oct 29, 2008 V.2
Table 4 Test condition, procedure and requirements
Chip Resistor Surface Mount
TEST METHOD
MIL-STD-202G-method 108A
IEC 60115-1 4.25.1
JIS C 5202-7.10
MIL-STD-202G-method 108A
IEC 60115-1 4.25.3
JIS C 5202-7.11
MIL-STD-202G-method 106F
IEC 60115-1 4.24.2
MIL-STD-202G-method 107G
MIL-R-55342D-para 4.7.5
IEC60115-1 4.13
IEC60115-1 4.33
1,000 hours at 70±5 °C applied RCWV
1.5 hours on, 0.5 hour off, still air required
1,000 hours at maximum operating temperature
depending on specification, unpowered
No direct impingement of forced air to the parts
Tolerances: 155±3 °C
Each temperature / humidity cycle is defined at 8
hours (method 106F), 3 cycles / 24 hours for 10d
with 25 °C / 65 °C 95% R.H, without steps 7a &
7b, unpowered
Parts mounted on test-boards, without
condensation on parts
Measurement at 24±2 hours after
test conclusion
YC124: -55/+155 °C
TC124: -55/+125 °C
Note: Number of cycles required is 300. Devices
unmounted
Maximum transfer time is 20 seconds. Dwell time
is 15 minutes. Air – Air
2.5 times RCWV or maximum overload voltage
whichever is less for 5 sec at room temperature
Device mounted on PCB test board as described,
only 1 board bending required
3 mm bending
Bending time: 60±5 seconds
Ohmic value checked during bending
PROCEDURE
YC/TC
SERIES
124 (RoHS Compliant)
REQUIREMENTS
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(1%+0.05 Ω)
<50 mΩ for Jumper
±(2%+0.05 Ω)
<100 mΩ for Jumper
±(0.5%+0.05 Ω) for 10 KΩ to
10 MΩ
±(1%+0.05 Ω) for others
<50 mΩ for Jumper
±(2%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
±(1%+0.05 Ω)
<50 mΩ for Jumper
No visible damage
Product specification
www.yageo.com
7
9