MC12CD100D-T Cornell Dubilier Electronics (CDE), MC12CD100D-T Datasheet - Page 3

• Manufacturer Part Number: MC12CD100D-T
• Description: CAP 10PF 500V MICA CHIP 1210
• Manufacturer: Cornell Dubilier Electronics (CDE)
• Series: MCr

Specifications of MC12CD100D-T

• Capacitance: 10pF
• Voltage - Rated: 500V
• Tolerance: ±0.5pF
• Dielectric Material: Mica
• Mounting Type: Surface Mount
• Package / Case: 1210 (3225 Metric)
• Operating Temperature: -55°C ~ 125°C
• Features: RF, High Q, Low Loss
• Size / Dimension: 0.126" L x 0.098" W (3.20mm x 2.50mm)
• Height: 0.079" (2.00mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Spacing: -
• Other names: 338-1002-2

1.032
Specifications
Marking
Example:
R1 = 43 pF
Capacitance
when measured as follows:
Dissipation Factor
than 0.1% when measured as
above.
Type MC, Surface-Mount Mica Chip Capacitors
Value
Base
10
11
12
13
15
16
18
20
22
24
25
27
30
33
35
36
39
After-Test Limits
IL=Initial Limit
IL=Initial Limit
R1
Life Test
Vibration Resistance
Bending Test
Moisture Res.
Solderability
Heat Resistance
Solder Heat Res.
1–1000 pF @ 1 MHz
Capacitance Code
> 1000 pF @ 1 kHz
Code
Ltr.
M
D
G
H
N
Q
A
B
C
K
E
F
a
L
b
P
J
Test
Multiplier
IV=Initial Value
BRN/GRN=1000 Vdc
is within tolerance
X 0.1
X 1
X 10
X 100
X 0.01
Voltage Color
Value
brown=100 Vdc
Base
green=500 Vdc
40
43
45
47
50
51
56
60
62
68
70
75
80
82
90
91
is no more
Withstand
Voltage
Code
Code
No.
Ltr.
W
m
0
1
2
3
9
R
U
V
n
X
IL
IL
IL
IL
IL
IL
d
e
S
T
Y
y
Z
f
t
Quality Factor (Q)
when measured at 1 MHz.
Insulation Resistance
less than 100 G
at 100 Vdc.
Withstanding Voltage
times the rated voltage and can be
applied up to 5 seconds without
damage.
Life Test:
125 3 C with 1.5 times rated volt-
age applied for 2000 (+72,–0)
hours. There will be no visual dam-
age and the capacitors will meet
the limits of the table below.
Vibration Resistance:
the capacitors to simple harmonic
motion with an amplitude of 0.06
inches; vary the frequency uni-
formly from 10 to 55 Hz and return
to 10 Hz, all in one minute. Repeat
that cycle continuously for two
hours in each of three mutually
perpendicular directions. There will
be no visual damage and the ca-
pacitors will meet the limits of the
table below.
Bending Test:
capacitors to printed-circuit boards.
Suspend each board between two
edges separated 3.5 inches with the
capacitor in the center and on the
Capacitance
Resistance
Insulation
1 to 80 pF
30 G
30 G
30 G
5 G
>80 pF
Range
IL
IL
[phone], Fax [phone]
E-mail: [e-mail]
Subject capacitors to
1605 East Rodney French Blvd.
http://www.cornell-dubilier.com
Solder attach the
when measured
New Bedford, MA 02744
500 to 3000
is as follows
IV 2% or .5pF
IV .5% or 1pF
IV 3% or .5pF
IV .5% or 1pF
IV 1% or 1pF
(whichever >)
Min. Q
Capacitance
3000
Subject
is two
IL
is no
underside. Press in the center of the
suspension until the board flexes
downward 0.1 inches. There will be
no visual damage and the capaci-
tors will meet the limits of the table
below during and after the bend-
ing.
Moisture Resistance:
the capacitors to 40 2 C at 90 to
95% humidity for 500 (+24,–0)
hours. Return to room ambient for
24 hours. There will be no visual
damage and the capacitors will
meet the limits of the table below.
Temperature Coefficient
and Drift:
tors’ capacitance at 25 C, –55 C,
25 C, 125 C, and at 25 C—all
perature. The capacitance will meet
the limits of the Characteristic table
in Ordering Information.
Heat Resistance:
pacitors to 125 2 C for 2 (+1,–0)
hours. Then the insulation resis-
tance will be no less than 5G .
Solderability:
onds in molten solder with 2.5% sil-
ver at 270 5 C, solder coverage will
be no less than 90% when exam-
ined at 10X magnification for flow
soldering and no less than 75% for
reflow soldering.
Solder Heat Resistance:
ject the capacitors to molten solder
as above with 5 minutes preheating
at 150 3 C. There will be no visual
damage and the capacitors will
meet the limits of the table below.
3 C—after stabilizing at each tem-
Your Source For Capacitor Solutions
150% max IL
150% max IL
DF
IL
IL
IL
IL
Measure the capaci-
C O R N E L L
D U B I L I E R
After 2 0.5 sec-
2/3xIL
2/3xIL
Subject the ca-
IL
IL
IL
Q
Subject
Sub-