G5Y-1-DC5 Omron, G5Y-1-DC5 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
G5Y-1-DC5
Manufacturer Part Number
G5Y-1-DC5
Description
RELAY PC MNT HI-FREQ SPDT 5VDC
Manufacturer
Omron
Series
G5Y-1r
Datasheet
1.G5Y-1-DC5.pdf
(8 pages)
Specifications of G5Y-1-DC5
Relay Type
RF
Circuit
SPDT (1 Form C)
Contact Rating @ Voltage
0.01A @ 24VAC/DC
Coil Type
Standard
Coil Current
60.2mA
Coil Voltage
5VDC
Control On Voltage (max)
3.75 VDC
Control Off Voltage (min)
0.5 VDC
Mounting Type
Through Hole
Termination Style
PC Pin
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
G5Y1DC5
Z723
Z723
G5Y-1
Dimensions
Unit: mm (inch)
Note: Parts marked with
Hints on Correct Use
How to design PC Board
Thickness of PC board
PC boards are generally available in the following
thicknesses: 0.8 (0.03), 1.0 (0.04), 1.2 (0.05), 1.6 (0.06), and
2.0 mm (0.08 in). In determining the thickness of the PC
board to be used, the pattern widths of the microstrips must
be taken into account. First, determine the applicable pattern
widths based on the intended arrangement of components on
the PC board. Then select the appropriate PC board
thickness.
PC board material
The base materials of PC boards can be divided into two
types: epoxy type and phenolic type. For high-frequency
circuits, glass epoxy type double-sided PC boards are
recommended because of their distinct dielectric constant
and material stability. However, paper epoxy type or paper
phenolic type single-sided PC boards may also be used if
cost factor is essential. Refer to “Examples of packaging
design” for mounting the relay on a single-sided PC board.
Preparation for pattern design
Relay mounting direction
The mounting direction of each relay must be taken into
account for the relay to function with maximum performance.
Shock resistance is one of the representative relay
performance characteristics greatly influenced by the relay
mounting direction. Refer to the Shock Resistance
Characteristic in “Characteristic Data” section.
Note that the shock resistance of a relay (NC contact), with its
coil in the nonenergized state, is governed greatly by the
mounting direction of the relay.
RELAY
PC BOARD SELECTION
PATTERN DESIGN
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
and
indicate mounting direction mark on G5Y relay.
Terminal arrangement/
Internal connections
(bottom view)
Terminal hole diameters, land diameters, and land shapes
(DC circuit)
Terminal hole diameter and land diameter
Select the appropriate terminal hole diameter and land
diameter from the following table based on the PC board
mounting hole drawing. Land diameters may be reduced to
less than those listed below if thru-hole connection process is
to be employed.
Terminal hole diameters and land diameters
Unit: mm (inch)
Terminal hole
diameter
Nominal value
0.6 (0.02)
0.8 (0.03)
1.0 (0.04)
1.2 (0.05)
1.3 (0.05)
1.5 (0.06)
1.6 (0.06)
2.0 (0.08)
Minimum
land
diameter
1.5 (0.06)
1.8 (0.07)
2.0 (0.08)
2.5 (0.10)
3.0 (0.12)
Mounting holes
(bottom view)
Tolerance
0.1 ( 0.004)
G5Y-1
5