ARXP1003 Panasonic Electric Works, ARXP1003 Datasheet - Page 4

• Manufacturer Part Number: ARXP1003
• Description: RELAY SPDT 3GHZ 60W 3VDC
• Manufacturer: Panasonic Electric Works
• Series: ARXPr

Specifications of ARXP1003

• Relay Type: RF
• Circuit: SPDT (1 Form C)
• Contact Rating @ Voltage: 0.5A @ 30VDC
• Coil Type: Standard
• Coil Current: 66.7mA
• Coil Voltage: 3VDC
• Control On Voltage (max): 2.25 VDC
• Control Off Voltage (min): 0.3 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 255-2718

DIMENSIONS
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be
rectangular. If it includes ripple, the ripple
factor should be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
To ensure accurate operation, the voltage
on both sides of the coil should be ±5%
(at 20°C 68°F) of the nominal coil
voltage.
Also, please note that the pick-up and
drop-out voltages (set and reset voltages)
will change depending on operation
temperature and conditions of use.
Keep the coil allowable voltage ripple
ratio to no more than 5%.
3. External magnetic field
Since RX-P relays are highly sensitive
polarized relays, their characteristics will
be affected by a strong external magnetic
field. Avoid using the relay under that
condition.
7-0.40 to 0.45 dia.
7-.016 to .018 dia.
Solder to the
PC board earth.
2-0.6×0.3
2-.024×.012
.362
9.2
2.63
.104
(mm inch)
.008
0.2
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
2.54
.100
20.5
.807
Tolerance: ±0.3
Part No.
External dimensions
Lot No.
4. Cleaning
For automatic cleaning, the boiling
method is recommended. Avoid
ultrasonic cleaning which subjects the
relays to high frequency vibrations, which
may cause the contacts to stick.
It is recommended that alcoholic solvents
be used.
5. Soldering
1) Please meet the following conditions if
this relay is to be automatically soldered.
(1) Preheating: Max. 120°C
(terminal solder surface) for max. 120
seconds
(2) Soldering: Max. 260±5°C
for max. 6 seconds
2) Please meet the following conditions if
this relay is to be soldered by hand.
(1) 260°C
(2) 350°C
*In addition, when soldering the case to
the PC board, the plating may swell
depending on the soldering conditions.
6. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +70°C
when 60 to 70°C
time is 1 second maximum and ON time
is 10% maximum.)
12.4
.488
3.0
.118
(2.04)
(.080)
±.012
500°F
662°F
7.62
.300
–40 to +158°F
for max. 10 seconds
for max. 3 seconds
140 to
(2.74)
(.108)
158°F, the pulse
(Deenergized condition)
NC
248°F
Single side stable
-
14
(However,
1
500±41°F
13
12
COM
11
10
7.62
.300
9
NO
+
PC board pattern (Bottom view)
7
8
2.54
.100
Schematic (Bottom view)
0.90
.035
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under
high temperature and high humidity
conditions. Condensation will cause
deterioration of the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C 32°F. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
0.9 dia. hole
.035 dia. hole
RESET
+
(Reset condition)
14
1
(Avoid freezing
when used at
temperatures
lower than
0°C 32°F)
1 coil latching
13
-40
-40
2.54
.100
12
COM
Tolerance range
11
10
85
RX-P (ARXP1)
5
9
32
SET
0
Temperature, °C
-
(Avoid
condensation
when used at
temperatures
higher than
0°C 32°F)
Humidity, %R.H.
2 coil latching only
7
8
R 0.45
Tolerance: ±0.1
.018
RESET
-
(Reset condition)
14
1
2 coil latching
°F
13
158
70
12
COM
11
10
±.004
+
6
9
SET
+
7
8