TXD2SA-L-4.5V-6 Panasonic Electric Works, TXD2SA-L-4.5V-6 Datasheet - Page 7
![RELAY LATCH 2A 4.5VDC 150MW SMD](/photos/28/44/284459/txd2sa-l-4_5v-6_sml.jpg)
TXD2SA-L-4.5V-6
Manufacturer Part Number
TXD2SA-L-4.5V-6
Description
RELAY LATCH 2A 4.5VDC 150MW SMD
Manufacturer
Panasonic Electric Works
Series
TX-Dr
Datasheet
1.TXD2SS-12V-Z.pdf
(12 pages)
Specifications of TXD2SA-L-4.5V-6
Relay Type
General Purpose
Circuit
DPDT (2 Form C)
Contact Rating @ Voltage
2A @ 30VDC
Coil Type
Latching, Single Coil
Coil Current
33.3mA
Coil Voltage
4.5VDC
Control On Voltage (max)
3.38 VDC
Mounting Type
Surface Mount
Termination Style
Gull Wing
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Control Off Voltage (min)
-
Other names
255-2883
2. Specifications
Notes: *1 M.B.B. type models are only available in 2,500 V surge breakdown voltage type.
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
Characteristics
*2 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
*3 The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to [6] AMBIENT ENVIRONMENT
actual load. (AgPd contact type or SX relays are available for low level load switching [10V DC, 10mA max. level])
in GENERAL APPLICATION GUIDELINES.
Arrangement
Contact resistance (Initial)
Contact material
Nominal switching capacity
Max. switching power
Max. switching voltage
Max. switching current
Min. switching capacity (Reference value)*
Nominal operating
power
Insulation resistance (Initial)
Breakdown
voltage (Initial)
Surge breakdown
voltage (Initial)
Temperature rise (at 20°C 68°F)
Operate time [Set time] (at 20°C 68°F)
Release time [Reset time] (at 20°C 68°F)
Shock
resistance
Vibration
resistance
Mechanical
Electrical
Conditions for operation, transport and
storage*
Max. operating speed (at rated load)
3
Single side stable
1 coil latching
Between open contacts
Between contact and coil
Between contact sets
Between open contacts
Between contacts and
coil*
Functional
Destructive
Functional
Destructive
Item
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
1
2
1,000 Vrms for 1min. (Detection current: 10mA)
1,500 Vrms for 1min. (Detection current: 10mA)
2,000 Vrms for 1min. (Detection current: 10mA)
3,000 Vrms for 1min. (Detection current: 10mA)
Min. 1,000MΩ (at 500V DC) Measurement at same location as “Initial breakdown voltage” section.
Surge breakdown voltage 6,000 V and 6,000 V
Min. 5×10
200mW (1.5 to 12 V DC), 230mW (24 V DC)
280mW (1.5 to 12 V DC), 310mW (24 V DC)
150mW (1.5 to 12 V DC), 170mW (24 V DC)
230mW (1.5 to 12 V DC), 250mW (24 V DC)
Max. 4 ms [Max. 4 ms] (Nominal coil voltage applied to the coil, excluding contact bounce time.)
Max. 4 ms [Max. 4 ms] (Nominal coil voltage applied to the coil, excluding contact bounce time.)
AgPd contact: 1 A 30 V DC (resistive load)
Standard contact: 2 A, AgPd contact: 1 A
AgPd contact: 30 W (DC) (resistive load)
6,000 V (High breakdown voltage) types:
6,000 V (High breakdown voltage) type:
6,000 V (High breakdown voltage) type:
6,000 V (High breakdown voltage) type:
Surge breakdown voltage 2,500 V type:
Surge breakdown voltage 2,500 V type:
Surge breakdown voltage 6,000 V and
(Half-wave pulse of sine wave: 6 ms;
1,500 V (10×160µs) (FCC Part 68)
(High breakdown voltage) types:
Min. 10
Standard contact: 2 A 30 V DC,
Standard contact: 60 W (DC),
2,500 V, 2 × 10µs (Telcordia)
2,500 V and 6,000 V types:
2,500 V and 6,000 V types:
2,500 V and 6,000 V types:
5
Surge breakdown voltage
Surge breakdown voltage
Surge breakdown voltage
Surge breakdown voltage
Surge breakdown voltage
Surge breakdown voltage
(1 A 30 V DC resistive) (at 20 cpm)
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
AgPd contact (low level load): AgPd+Au clad (stationary), AgPd (movable)
detection time: 10µs.)
Min. 10
6,000 V, 1.2 × 50µs
5
10 to 55 Hz at double amplitude of 3.3 mm (Detection time: 10µs.)
(2 A 30 V DC resistive),
Min. 750 m/s
220 V DC
Min. 1,000 m/s
2 Form C
(By resistive method, nominal coil voltage applied to the coil;
8
Ambient temperature: –40°C to +85°C
(at 180 cpm)
1,000 Vrms for 1min. (Detection current: 10mA)
Max. 100 mΩ (By voltage drop 6 V DC 1A)
contact carrying current: 2A [1A: M.B.B.].)
10 to 55 Hz at double amplitude of 5 mm
2
2
Standard contact: Ag+Au clad,
{100G} (Half-wave pulse of sine wave: 6 ms.)
Approx. 2 g
Max. 50°C
10µA10mV DC
(without diode)
Specifications
20 cpm
2,000 Vrms for 1min. (Detection current: 10mA)
.071 oz
122°F
500 Vrms for 1min. (Detection current: 10mA)
250mW (1.5 to 12 V DC), 270mW (24 V DC)
Min. 10
(Half-wave pulse of sine wave: 11 ms;
–40°F to
5
2,500 V, 2 × 10µs (Telcordia)
1 A 30 V DC (resistive load)
(1 A 30 V DC resistive) (at 20 cpm)
30 W (DC) (resistive load)
2 Form D (M.B.B.type)*
detection time: 10µs.)
Min. 10
Min. 500 m/s
+185°F;
110 V DC
7
(at 180 cpm)
1 A
—
—
2
1
TX-D