G2R-14-AC24 Omron, G2R-14-AC24 Datasheet - Page 25

• Manufacturer Part Number: G2R-14-AC24
• Description: RELAY SPDT 10A 24VAC PC MT
• Manufacturer: Omron
• Series: G2Rr

Specifications of G2R-14-AC24

• Relay Type: General Purpose
• Coil Resistance: 260 Ohms
• Contact Form: SPDT (1 Form C)
• Contact Rating (current): 10A
• Switching Voltage: 380VAC, 125VDC - Max
• Coil Type: Standard
• Coil Current: 37.5mA
• Coil Voltage: 24VAC
• Turn On Voltage (max): 19.2 VAC
• Turn Off Voltage (min): 7.2 VAC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: SPDT (1 Form C)
• Contact Rating @ Voltage: 10A @ 250VAC
• Control On Voltage (max): 19.2 VAC
• Control Off Voltage (min): 7.2 VAC
• Contact Rating: 10 A
• Contact Termination: Solder Pin
• Mounting Style: Through Hole
• Power Consumption: 0.9 VA
• Contact Material: Silver Alloy
• Coil Voltage Vac Nom: 24V
• Contact Current Max: 10A
• Contact Voltage Ac Nom: 250V
• Contact Voltage Dc Nom: 30V
• Contact Configuration: SPDT
• Current, Rating: 10 A
• Function: Power
• Number Of Pins: 5
• Power, Rating: 2500⁄300 VA⁄W
• Standards: UL, CSA, VDE, CE
• Termination: Through Hole
• Voltage, Control: 24 VAC
• Voltage, Rating: 380 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G2R14AC24; Z843

■ Designing Power Circuit
Since many documents and reference books on the power circuit are
available, a detailed description is omitted here.
■ Connection of Surge
Note: This graph is plotted by measuring the surge voltage in the line
When connecting a surge suppressor, pay attention to the following
points:
1. Place the surge suppressor near the device to be protected. For
External surge
* In the circuit above, varistors B
** Resistor R protects diode bridge D from the inrush current
*** C
example, to protect a device from external surge, set the surge
suppressor at the inlet of the device’s power cable.
To suppress an internal surge, the suppressor must be placed
near the surge generating source.
Suppressor
power circuit elements, as well as elements related to the
power circuit, in case the voltage on the power line experi-
ences surges (due to lightning or the surge voltage gener-
ated in other devices connected to the power circuit).
Connect an appropriate surge suppressor across the output
terminals of the power circuit to prevent a surge voltage
from being generated. The surge suppressor must keep the
surge voltage, if generated, from exceeding the breakdown
voltage of each element in the power circuit.
that flows through the power circuit upon power application.
Although the resistance of R is determined according to the
resistance of the load coil and the ratings of the diodes, the
use of a resistor having a resistance of 0.1 to 100Ω is rec-
ommended.
large as possible to reduce the ripple percentage.
1
of low-tension overhead wiring (cable length: 200 to 500 m).
is a smoothing capacitor. Its capacitance must be as
1
to B
4
are used to protect the
Electromechanical Relays
Internal surge
2. The cable for connecting the surge suppressor must be as short
3. When using a surge suppressor between cable and ground, the
■ Countermeasures Against
In case the supply voltage fluctuates heavily, insert a regulated volt-
age circuit or constant-voltage circuit in the application circuit as
shown below.
Relays consume more power than semiconductor elements. The fol-
lowing circuit configuration is recommended to improve the charac-
teristics.
as possible in length, and thick enough in diameter so that it can
sufficiently withstand the surge current. The short length and thick
diameter are important to reduce the inductance and generated
voltage, and to protect the device from heat damage.
lower the ground resistance of the surge suppressor, the better
the protective effect of the surge suppressor. Perform grounding
at a ground resistance of 10Ω or less.
Supply Voltage Fluctuation
Technical Information
25