QW1 TechTools, QW1 Datasheet - Page 16

• Manufacturer Part Number: QW1
• Description: PROGRAMMER PIC MCU QUICKWRITER
• Manufacturer: TechTools
• Series: QuickWriter™r
• Type: QuickWriterr

Specifications of QW1

• Contents: MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
• For Use With/related Products: PIC Micro® MCU
• For Use With: CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF

14
Details
Shortcuts
QuickWriter Help 2.1
The following will be disabled when a HEX file is opened, if the "Disable Option Editing for this file"
option has been selected:
A detailed procedure for setting options for production personnel is described below but the
general procedure is to Open the HEX file, set all desired options, select "Disable Option Editing"
in "General Options", then select "File - Save Option Settings". The control file has now been
created and modified (resides in the same directory as the HEX file), and is now ready for the
production department.
To configure a HEX file for archiving or production use, follow the procedure described here.
1.
2.
3.
4.
5.
6.
7.
MCU selection.
Auto Options, HEX Options and General Options.
Code, FUSE, ID and Calibration editors.
Manual access to tasks in the "Programming Tasks" tree or MCU Section menu.
ALL programming functions except Auto Run, Erase, Blank Check and Verify.
Open the desired HEX file from the directory it will be used in if possible.
Verify the MCU, Configuration Word and ID location settings. If the MCU and Configuration
Word are incorrect you will need to make the necessary changes, then save the HEX file
with ALL "Save Hex Options" enabled or select the proper overrides in HEX Options .
After saving the hex file, re-open it and re-verify the MCU, Configuration Word and etc. If
everything is correct, proceed with the next step.
Go to the "Options - Auto Options" and select each option to be performed during
programming. Each selected item will be performed when the production department chooses
"Auto Run" (or F4 or Alt+A).
If you have enabled Serialization, verify the serial number length and address settings to
prevent overlapping valid code or EE data. Also verify the "last serial number" and "Auto
Increment" settings (see:
After all settings have been verified, select "Disable Option Editing.." in the "Misc. Options"
section of the "General Options". You may also want to select "Disable Read Functions" in
this same location.
Select "File - Save Option Settings" from the main menu, then close the program.
Copy the HEX file and the corresponding control file (hexfilename.QWC) to the desired
location for production accessability. The production department can now open the HEX file
without fear of accidental changes.
Alt+E, i (disable option editing for testing)
Alt+E, E (enable option editing for further editing)
Using Serial
Numbers).
©2006 TechTools