DEMOBOARD TLE 7230G Infineon Technologies, DEMOBOARD TLE 7230G Datasheet

no-image

DEMOBOARD TLE 7230G

Manufacturer Part Number
DEMOBOARD TLE 7230G
Description
BOARD DEMO FOR TLE 7230G 1.0
Manufacturer
Infineon Technologies
Datasheet

Specifications of DEMOBOARD TLE 7230G

Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
DEMOBOARDTLE7230GIN
Data Sheet, V1.1, February 2008
SPIDER - TLE7230G
S P I D r i v e r f o r E n h a n c e d R e l a y C o n t r o l
E i g h t C h a n n e l L o w - S i d e S w i t c h
A u t o m o t i v e P o w e r

Related parts for DEMOBOARD TLE 7230G

DEMOBOARD TLE 7230G Summary of contents

Page 1

SPIDER - TLE7230G ...

Page 2

Table of Contents Product Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3

SPI Driver for Enhanced Relay Control The SPIDER - TLE7230G is an eight channel low-side power switch in PG-DSO-24-13 package providing embedded protective functions especially designed for standard relays in automotive applications. A serial peripheral interface (SPI) is ...

Page 4

Basic Features • 16 bit SPI for diagnostics and control • SPI providing daisy chain capability • 3.3 V and 5 V compatible SPI • A configurable input pin offers complete flexibility for PWM operation • Stable behavior at under ...

Page 5

Overview The SPIDER - TLE7230G is an eight channel low-side relay switch (1.0 Ω per channel) in PG-DSO-24-13 package providing embedded protective functions. The 16 bit serial peripheral interface (SPI) is utilized for control and diagnosis of the device ...

Page 6

Terms Following figure shows all terms used in this data sheet CLK ...

Page 7

Pin Configuration 2.1 Pin Assignment SPIDER - TLE7230G OUT2 OUT3 GND GND GND GND OUT4 OUT5 VSO Figure 3 Pin Configuration PG-DSO-24-13 2.2 Pin Definitions and Functions Pin Symbol Power Supply 23 VDD 11 VSO ...

Page 8

Pin Symbol 4 OUT3 9 OUT4 10 OUT5 15 OUT6 16 OUT7 Inputs 24 RST 2 IN SPI SCLK Data Sheet SPI Driver for Enhanced Relay Control I/O Function O Drain of power ...

Page 9

Electrical Characteristics 3.1 Maximum Ratings Stresses above the ones listed here may affect device reliability or may cause permanent damage to the device. Unless otherwise specified: Pos. Parameter Power Supply 3.1.1 Power supply voltage 3.1.2 VSO supply voltage 3.1.3 ...

Page 10

Unless otherwise specified: Pos. Parameter 3.1.11 Voltage at serial input pin 3.1.12 Voltage at serial output pin Temperatures 3.1.13 Junction Temperature 3.1.14 Dynamic temperature increase while switching 3.1.15 Storage Temperature ESD Susceptibility 3.1.16 ESD susceptibility HBM 0.3 ...

Page 11

Block Description and Electrical Characteristics 4.1 Power Stages The SPIDER - TLE7230G is an eight channel low-side relay switch. The power stages are built by N-channel vertical power MOSFET transistors. 4.1.1 Power Supply The SPIDER - TLE7230G is supplied ...

Page 12

The input signal can be configured to be used as control signal of the output stages for each channel separately. The channels differ from the channels the mapping behavior. Please refer to The ...

Page 13

Timing Diagrams The power transistors are switched on and off with a dedicated slope via the OUT bits of the serial peripheral interface SPI. The switching times equally. CS SPI 80% 20% Figure 6 Switching a ...

Page 14

Electrical Characteristics Unless otherwise specified: V typical values Pos. Parameter Power Supply 4.1.1 Power supply voltage 4.1.2 Power supply current 4.1.3 Power supply reset current 4.1.4 Power-on reset threshold voltage Output Characteristics 4.1.5 On-State resistance ...

Page 15

Unless otherwise specified: V typical values Pos. Parameter Reset 4.1.13 L level of pin RST 4.1.14 H level of pin RST 4.1.15 L-input pull-up current through pin RST 4.1.16 H-input pull-up current through pin RST Thermal ...

Page 16

Command Description IMCR Input Mapping Configuration Register 7 6 MAP7 MAP6 MAP5 rw rw Field Bits Type Description MAPn 7-0) BOCR Boolean Operator Configuration Register 7 6 BOL7 BOL6 BOL5 rw rw Field Bits Type ...

Page 17

SRCR Slew Rate Configuration Register 7 6 SLE7 SLE6 SLE5 rw rw Field Bits Type Description n rw SLEn (n = 7-0) CTL Output Control Register 7 6 OUT7 OUT6 OUT5 rw rw Field Bits Type Description n rw OUTn ...

Page 18

Protection Functions The device provides embedded protective functions. Integrated protection functions are designed to prevent IC destruction under fault conditions described in this data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed ...

Page 19

OLCR.OVL = D(lim) t d(fault) Figure 8 Over Load Behavior 4.2.2 Over Temperature Protection A temperature sensor for each channel causes an overheated channel n to switch off immediately to prevent destruction. The behavior in ...

Page 20

Electrical Characteristics Unless otherwise specified: V typical values Pos. Parameter Over Load Protection 4.2.1 Over load current limitation 4.2.2 Over load shut-down delay time Over Temperature Protection 4.2.3 Over temperature shut-down threshold 4.2.4 Thermal hysteresis ...

Page 21

Command Description OLCR Over Load Configuration Register 7 6 OVL7 OVL6 OVL5 rw rw Field Bits Type Description OVLn 7-0) OTCR Over Temperature Configuration Register 7 6 OVT7 OVT6 OVT5 rw rw Field Bits Type ...

Page 22

Diagnostic Features The SPI of SPIDER - TLE7230G provides diagnosis information about the device and about the load. There are following diagnosis flags implemented: • The diagnosis information of the protective functions (flags CLn and Tn) of channel n ...

Page 23

Electrical Characteristics Unless otherwise specified: V typical values Pos. Parameter OFF State Diagnosis 4.3.1 Open load detection threshold voltage 4.3.2 Output pull-down diagnosis current per channel 4.3.3 Short to gnd detection threshold voltage 4.3.4 Output ...

Page 24

Command Description STA Output Status Monitor 7 6 OUT7 OUT6 OUT5 r r Field Bits Type Description OUTn 7-0) Data Sheet SPI Driver for Enhanced Relay Control OUT4 OUT3 ...

Page 25

Serial Peripheral Interface (SPI) The diagnosis and control interface is based on a serial peripheral interface (SPI). The SPI is a full duplex synchronous serial slave interface, which uses four lines: SO, SI, SCLK and CS. Data is transferred ...

Page 26

It is essential that the SCLK pin is in low state whenever chip select CS makes any transition Serial Input: Serial input data bits are ...

Page 27

MI SO device device 3 MCS MCLK time Figure 12 Data Transfer in Daisy Chain Configuration 4.4.3 Timing Diagrams t CS(lead SCLK SI SO Figure 13 Timing Diagram Data Sheet SPI Driver for Enhanced Relay ...

Page 28

Electrical Characteristics Unless otherwise specified 3 5.5 V, VSO dd V typical values: = 5.0 V, VSO Pos. Parameter Power Supply 4.4.1 Power supply voltage for SO buffer Input Characteristics (CS, SCLK, SI) 4.4.2 ...

Page 29

Unless otherwise specified 3 5.5 V, VSO dd V typical values: = 5.0 V, VSO Pos. Parameter Timings 4.4.11 Serial clock frequency 4.4.12 Serial clock period 4.4.13 Serial clock high time 4.4.14 Serial clock low ...

Page 30

SPI Protocol The SPI protocol of the SPIDER - TLE7230G provides two types of registers. The control registers and the diagnosis registers. After power-on reset, all register bits set to default values CMD ...

Page 31

SO Standard Diagnosis CH7 CH6 Field Bits Type Description CHn (2n+1 7- Second Frame of Read Command Field Bits Type Description ...

Page 32

Register Overview Name W/R Addr 7 IMCR W/R 001 MAP7 MAP6 MAP5 MAP4 MAP3 MAP2 MAP1 MAP0 08 B BOCR W/R 010 BOL7 BOL6 BOL5 BOL4 BOL3 BOL2 BOL1 BOL0 00 B OLCR W/R 011 OVL7 OVL6 OVL5 OVL4 ...

Page 33

Package Outlines 1.27 +0. Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area Figure 14 PG-DSO-24-13 (Plastic Green Dual ...

Page 34

Revision History Version Date Changes V1.1 08-02-19 Initial version of RoHS-compliant derivate of SPIDER - TLE7230G Page 4: added AEC certified statement Page 4 and 33: added RoHS compliance statement and Green product feature Page 3: updated package picture ...

Page 35

... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...

Page 36

... Published by Infineon Technologies AG ...

Related keywords