MPC5534EVBGHS Freescale Semiconductor, MPC5534EVBGHS Datasheet - Page 55

• Manufacturer Part Number: MPC5534EVBGHS
• Description: KIT EVAL GREEN HILLS SOFTWARE
• Manufacturer: Freescale Semiconductor
• Type: Microcontrollerr

Specifications of MPC5534EVBGHS

• Contents: Eval Board and Demo Software
• Processor To Be Evaluated: MPC55xx
• Data Bus Width: 32 bit
• Interface Type: RS-232, Ethernet
• Core Architecture: Power
• For Use With/related Products: MPC5534
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Freescale Semiconductor
Table
Table
Table
Table
Table
Location
4, EMI Testing Specifications: Changed the maximum operating frequency from 82 to f
6, VCR/POR Electrical Specifications:
7, Power Sequence Pin Status for Fast Pads: Changed title to Pin Status for Fast Pads During the Power Sequence
8, Power Sequence Pin Status for Medium/Slow Pads:
9, DC Electrical Specifications:
• Added footnote 1 to specs 1, 2, and 3 that reads: On power up, assert RESET before V
• Subscript all symbol names that appear after the first underscore character.
• Removed ‘Tj ‘ after ‘150 C’ in Spec 10, Characteristic column:
• Added footnote 1 to specs 1, 2, and 3 that reads: On power up, assert RESET before V
• Added to Spec 2:
• Spec 3: Added new footnote 3 for both lines: ‘It is possible to reach the current limit during ramp up--do not treat
• Spec 5: Changed old Footnote 1 (now footnote 2): ‘User must be able to supply full operating current for the 1.5 V
• Specs 7 and 10: added ‘at Tj ‘ at the end of the first line in the second column: Characteristic.
• Spec 10:
• Deleted footnote 9 Preliminary value, Final specification pending characterization.
• Changed title to Pin Status for Medium and Slow Pads During the Power Sequence
• Updated preceding paragraph.
• Spelled out meaning of the slash ‘/’ as ‘and’. Still confusing. Deleted ‘I/O’ from the specs to improve clarity.
• Added footnote that reads: V
• Spec 20, column 2, Characteristics,’ Slow and medium output high voltage (I
• Spec 20, column 4, Min: Added a blank line before and after ‘0.80  V
• Spec 22, column 2, ’Slow and medium output low voltage (I
• Spec 22, column 5, Max: Added a blank line before and after ‘0.20  V
• Spec 26: Changed ‘AN[12]_MA[1]_SDO’ to ‘AN[13]_MA[1]_SDO’.
• Spec 28: Changed 82 MHz to f
• Footnote 9: Changed from ‘Preliminary. Final specification pending characterization.’ to
negate (internal POR). RESET must remain asserted until the power supplies are within the operating conditions
as specified in
fall outside the operating conditions and until the internal POR asserts.
negate (internal POR). RESET must remain asserted until the power supplies are within the operating conditions
as specified in
fall outside the operating conditions and until the internal POR asserts.
this event as a short circuit current.’
supply when the 3.3 V supply reaches this range.” to ‘Supply full operating current for the 1.5 V supply when the
3.3 V supply reaches this range.”
a range of 1.6–3.6 V if EBTS =1.
Created a left-justified second line and moved ‘I
the parentheses. Created a left-justified third line that reads ‘I
and moved ‘I
left-justified third line that reads ‘I
line.
illustration of the I
3.3 V (V
3.3 V (V
• Added cross-reference to footnote 6: ‘I
• Added old footnote 5 new footnote 6.
• Added a new footnote 7, ‘Refer to
• Rewrote old footnote 8 (new footnote 9) to: Represents the worst-case external transistor BETA. It is measured
V
on a per part basis and calculated as (I
Table 30. Table and Figure Changes Between Rev. 3.0 and 4.0 (continued)
RC33
DDSYN
DDSYN
= 3.1 V, V
OL_S
) POR negated (ramp down)
) POR asserted (ramp up)
Table 9
Table 9
DD_STBY
= 2.0 mA.’ from the 1st line to the second line and deleted the parentheses. Created a
VRCCTL
DC Electrical Specifications. On power down, assert RESET before any power supplies
DC Electrical Specifications. On power down, assert RESET before any power supplies
MPC5534 Microcontroller Data Sheet, Rev. 5
values interpolated for these temperature values.’
= 2.2 V.’ Changed ‘(@ V
DDE2
MAX
OL_S
and V
MHz.
Table 1
= 1.0 mA.’
DDE3
VRCCTL
Description of Changes
DD
for the maximum operating frequency.’

are limited to 2.25–3.6 V only if EBTS = 0; V
OH_S
I
is measured at the following conditions: V
VRCCTL
DD
= –2.0 mA’ from the 1st line to the second line and deleted
= 1.35 V, f
).
Min 0.0
Min 0.0
OL_S
OH_S
Revision History for the MPC5534 Data Sheet
sys
= 2.0 mA):’ Created a left-justified second line
= –1.0 mA.’
= f
DDEH
MAX
DDEH
Max 0.30
Max 0.30
’ and put ‘0.85  V
)‘ to ‘(@ f
’ and put ‘0.15  V
OH_S
MAX
.
= –2.0 mA):’
sys
POR15
POR15
V
V
= f
‘Figure 3
MAX
DDE2
, V
, V
DDEH
DD
).
POR33
POR33
= 1.35 V,
DDEH
and V
’ on the last line.
shows an
’ on the last
, and V
, and V
DDE3
POR5
POR5
have
55