EDK2215 Renesas Electronics America, EDK2215 Datasheet

Page 1

... EDK2215 U M SER ANUAL F H8S/2215 FLASH M N CHIP ICROCONTROLLER ...

Page 2

Preface Cautions 1. This document may be, wholly or partially, subject to change without notice. 2. All rights reserved. No one is permitted to reproduce or duplicate, in any form, a part or this entire document without Hitachi Micro Systems ...

Page 3

T C ABLE OF ONTENTS ............................................................................................................................................. 3 ABLE OF ONTENTS ....................................................................................................................................... 4 TART UP NSTRUCTIONS 2.1. INSTALLING THE EVALUATION DEVELOPMENT KIT (EDK)........................................................................... 4 2.2. SERIAL CONNECTION ....................................................................................................................................... 4 2.3. POWER SUPPLY ................................................................................................................................................ ...

Page 4

TART UP NSTRUCTIONS 2. NSTALLING THE VALUATION Please refer to the quick start guide provided for initial installation of the EDK. A copy of the quick start guide and other information relating to this ...

Page 5

EDK B L OARD AYOUT The diagram shows a general layout of the EDK board. FLASH Programming Power NMI Switch BOOT LED Power LED User1 LED User2 LED RESET BOOT Switch Switch CJ5 9-Way D-Type CJ4 3.1. EDK B ...

Page 6

EDK O PERATION 4.1. USER INTERFACE The EDK provides three buttons for influencing the operation of the board. The purpose of each button is clearly marked next to it. Refer to the board layout for positions (Section 3) 1. ...

Page 7

C C RYSTAL HOICE The operating crystal frequency has been chosen to support the fastest operation with the fastest serial operating speeds. The value of the crystal is 14.7456MHz. The following table shows the baud rates and Baud Rate ...

Page 8

M M EMORY AP Table 4-4 illustrates the EDK memory map for mode 6. H’0000 0000 H’0003 FFFF H’0040 0000 H’0043 FFFF H’0044 0000 H’00BFFFFF H’00C00000 H’00DFFFFF H’00E00000 H’00FF8FFF H’00FF9000 H’00FFAFFF H’00FF B000 H’00FF EFBF H’00FF EFC0 H’00FF F7FF ...

Page 9

The user LEDs are connected to the following ports: LED Identifier ULED1 ULED2 4.7 USB I NTERFACE Pin 1 3 The VBUS pin of this USB module must be connected to the USB’s connector VBUS pin via a level shifter. ...

Page 10

B O OARD PTIONS The EDK has a number of configuration settings set by jumpers CJ4 ( CJ5 ( and zero-ohm links. Common EDK functions can be set using the jumpers as described ...

Page 11

– CJ5 SER ODE ETTINGS CJ5 is used to set the operating mode of the microcontroller. These jumpers must be fitted at all times to ensure correct operation of the EDK. Jumper CJ 5-A User Mode ...

Page 12

ERIAL ORT ELECTION The programming serial port is connected to the RS232 connector by default. This allows direct programming of the EDK using the supplied software tools. A secondary serial port is available on the microcontroller ...

Page 13

... E10A H EADER E10A/E10T is not supported on the EDK2215 5. OOT ONTROL The method for placing the microcontroller device in to Boot mode for reprogramming has been incorporated into a complex programmable logic device (CPLD). This is not necessary for most user designs but allows a measure of increased flexibility for the EDK designs ...

Page 14

M H ICROCONTROLLER EADER The following table lists the connections to each or the headers on the board. 6. EADER Pin Function EDK Symbol No 1 PC5, A5 PC5 3 PC3, A3 PC3 5 PC1, A1 PC1 ...

Page 15

H J2 EADER Pin Function EDK Symbol No 1 PC6, A6 PC6 3 PB0, A8 PB0 5 RESERVE NC22 7 RESERVE NC24 9 PB4, A12 PB4 11 PB6, A14 PB6 13 PA0, A16 PA0 15 PA2, A18, RxD2 PRXD ...

Page 16

C D ODE EVELOPMENT 7.1. HMON 7.1. ODE UPPORT The HMON library is built to support modes and 7. The library is also built with the number of parameter registers set to 3 (Default ...

Page 17

M M EMORY AP H'00000000 Vectors H'00001000 FDTInit H'00001119 H'00002000 CUser_Vectors H'00002003 H'00020000 PHMON CHMON H'0002248A On-Chip FLASH ROM H'0003F600 FDTUserModeMicr oKernel H'0003FDF9 H'0003FFFF H'00400000 External RAM H'0043FFFF H'00FFB000 On-chip RAM H'00FFE000 BHMON H'00FFED0E H'00FFEDB0 Stack H'00FFEFAF H'00FFEFBF External ...

Page 18

AUD ATE ETTING HMON has initially set to connect at 115200Baud. Should the user wish to change this, the value for the BRR in HMONserialconfiguser.c will need to be changed and the project re-built. Please refer ...