AD9445-IF-LVDS/PCB Analog Devices Inc, AD9445-IF-LVDS/PCB Datasheet - Page 28

• Manufacturer Part Number: AD9445-IF-LVDS/PCB
• Description: BOARD EVAL FOR >100MHZ LVDS
• Manufacturer: Analog Devices Inc

Specifications of AD9445-IF-LVDS/PCB

• Design Resources: Using AD8376 to Drive Wide Bandwidth ADCs for High IF AC-Coupled Appls (CN0002) Using AD8352 as an Ultralow Distortion Differential RF/IF Front End for High Speed ADCs (CN0046) Using ADL5562 Differential Amplifier to Drive Wide Bandwidth ADCs for High IF AC-Coupled Appls (CN0110)
• Number Of Adc's: 1
• Number Of Bits: 14
• Sampling Rate (per Second): 125M
• Data Interface: Parallel
• Inputs Per Adc: 1 Differential
• Input Range: 3.2 Vpp
• Power (typ) @ Conditions: 2.3W @ 125MSPS
• Voltage Supply Source: Single
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9445
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD9445
OPERATIONAL MODE SELECTION
Data Format Select
The data format select (DFS) pin of the AD9445 determines
the coding format of the output data. This pin is 3.3 V CMOS-
compatible, with logic high (or AVDD1, 3.3 V) selecting twos
complement and DFS logic low (AGND) selecting offset binary
format. Table 10 summarizes the output coding.
Output Mode Select
The OUPUT MODE pin controls the logic compatibility, as well
as the pinout of the digital outputs. This pin is a CMOS-compatible
input. With OUTPUT MODE = 0 (AGND), the AD9445 outputs
are CMOS compatible, and the pin assignment for the device is
as defined in Table 8. With OUTPUT MODE = 1 (AVDD1, 3.3
V), the AD9445 outputs are LVDS compatible, and the pin
assignment for the device is as defined in Table 7.
Duty Cycle Stabilizer
The DCS circuit is controlled by the DCS MODE pin; a CMOS
logic low (AGND) on DCS MODE enables the DCS, and logic
high (AVDD1, 3.3 V) disables the controller.
Table 10. Digital Output Coding
Code
16,383
8192
8191
0
VIN+ − VIN−
Input Span = 3.2 V p-p (V)
+1.600
0
−0.000195
−1.60
VIN+ − VIN−
Input Span = 2 V p-p (V)
+1.000
0
−0.000122
−1.00
Rev. 0 | Page 28 of 40
Digital Output
Offset Binary (D13••••••D0)
11 1111 1111 1111
10 0000 0000 0000
01 1111 1111 1111
00 0000 0000 0000
RF ENABLE
The RF ENABLE pin is a CMOS-compatible control pin that
optimizes the configuration of the AD9445 analog front end.
The crossover analog input frequency for determining the
RF ENABLE connection differs for the 105 MSPS and 125 MSPS
speed grades. For the 125 MSPS speed grade, connecting the
RF ENABLE to AGND optimizes SFDR performance for appli-
cations with analog input frequencies <210 MHz. For applications
with analog inputs >210 MHz, this pin should be connected to
AVDD1 for optimum SFDR performance. Connecting this pin to
AVDD1 reconfigures the ADC, thereby improving high IF and RF
spurious performance. Operating in this mode increases power dis-
sipation from AVDD2 by 150 mW to 200 mW. For the 105 MSPS
speed grade, connecting RF ENABLE to AGND optimizes SFDR
performance for applications with analog input frequencies
<230 MHz. For applications with analog inputs >230 MHz, this
pin should be connected to AVDD1 to optimize performance.
Digital Output
Twos Complement (D13••••••D0)
00 0000 0000 0000
01 1111 1111 1111
11 1111 1111 1111
10 0000 0000 0000