AD5252EVAL Analog Devices Inc, AD5252EVAL Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD5252EVAL
Manufacturer Part Number
AD5252EVAL
Description
BOARD EVAL FOR AD5252
Manufacturer
Analog Devices Inc
Type
Digital Potentiometerr
Datasheet
1.AD5252BRUZ10.pdf
(28 pages)
Specifications of AD5252EVAL
Rohs Status
RoHS non-compliant
Contents
Evaluation Board
For Use With/related Products
AD5252
AD5251/AD5252
RDAC/EEMEM Write
Setting the wiper position requires an RDAC write operation.
The single write operation is shown in Figure 27, and the
consecutive write operation is shown in Figure 28. In the
consecutive write operation, if the RDAC is selected and the
address starts at 00001, the first data byte goes to RDAC1 and
the second data byte goes to RDAC3. The RDAC address is
shown in
While the RDAC wiper setting is controlled by a specific RDAC
register, each RDAC register corresponds to a specific EEMEM
location, which provides nonvolatile wiper storage functionality.
The addresses are shown in Table 7. The single and consecutive
write operations also apply to EEMEM write operations.
There are 12 nonvolatile memory locations: EEMEM4 to
EEMEM15. Users can store a total of 12 bytes of information,
such as memory data for other components, look-up tables, or
system identification information.
In a write operation to the EEMEM registers, the device disables
the I
polling is required to determine the completion of the write
cycle. See the EEMEM Write-Acknowledge Polling section.
RDAC/EEMEM Read
The AD5251/AD5252 provide two different RDAC or EEMEM
read operations. For example, Figure 29 shows the method of
reading the RDAC0 to RDAC3 contents without specifying the
address, assuming Address RDAC0 was already selected in the
previous operation. If an RDAC_N address other than RDAC0
was previously selected, readback starts with Address N, followed
by N + 1, and so on.
Figure 30 illustrates a random RDAC or EEMEM read
operation. This operation allows users to specify which RDAC
or EEMEM register is read by issuing a dummy write command
to change the RDAC address pointer and then proceeding with
the RDAC read operation at the new address location.
2
C interface during the internal write cycle. Acknowledge
Table 6
.
Rev. B | Page 16 of 28
Table 7. Addresses for Writing (Storing) RDAC Settings
and User-Defined Data to EEMEM Registers
(R/ W = 0, CMD/ REG = 0, EE/ RDAC = 1)
A4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8. Addresses for Reading (Restoring) RDAC Settings
and User Data from EEMEM
(R/ W = 1, CMD/ REG = 0, EE/ RDAC = 1)
A4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Users can store any of the 64 RDAC settings directly to the EEMEM for AD5251,
or any of the 256 RDAC settings directly to the EEMEM for the AD5252. This
is not limited to current RDAC wiper setting
A3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
A3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
A2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
A2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
A1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
A1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
A0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Data Byte Description
Reserved
Read RDAC1 setting from EEMEM1
Reserved
Read RDAC3 setting from EEMEM3
Read user data from EEMEM4
Read user data from EEMEM5
Read user data from EEMEM6
Read user data from EEMEM7
Read user data from EEMEM8
Read user data from EEMEM9
Read user data from EEMEM10
Read user data from EEMEM11
Read user data from EEMEM12
Read user data from EEMEM13
Read user data from EEMEM14
Read user data from EEMEM15
Data Byte Description
Reserved
Store RDAC1 setting to EEMEM1
Reserved
Store RDAC3 setting to EEMEM3
Store user data to EEMEM4
Store user data to EEMEM5
Store user data to EEMEM6
Store user data to EEMEM7
Store user data to EEMEM8
Store user data to EEMEM9
Store user data to EEMEM10
Store user data to EEMEM11
Store user data to EEMEM12
Store user data to EEMEM13
Store user data to EEMEM14
Store user data to EEMEM15
1
1