IE-789046-NS-EM1 Renesas Electronics America, IE-789046-NS-EM1 Datasheet
IE-789046-NS-EM1
Specifications of IE-789046-NS-EM1
Related parts for IE-789046-NS-EM1
IE-789046-NS-EM1 Summary of contents
Page 1
... NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com Issued by: Renesas Electronics Corporation (http://www ...
Page 2
... Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “ ...
Page 3
µ µ µ µ µ µ µ µ © 1999, 2002 ...
Page 4
...
Page 5
... Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • ...
Page 6
... Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: • Device availability • Ordering information • Product release schedule • ...
Page 7
... Addition (a) Internal clock in Figure 3-3 External Circuits Used as System Clock Oscillator Addition of 3.3 Power Supply Voltage of Target Interface Modification of descriptions in 4.1 µ µ µ µ PD789046 Subseries p. 36 Addition of 4.2 µ µ µ µ PD789074 Subseries Addition of corresponding product names to Table A-1 Pin Assignments of NP-44GB, NP-44GB-TQ, and NP-H44GB-TQ p ...
Page 8
... PD789046 Subseries: • µ PD789074 Subseries: Target Readers This manual is intended for engineers who will use the IE-789046-NS-EM1 with the IE- 78K0S-NS or IE-78K0S-NS-A to perform system debugging. Engineers who use this manual are expected to be thoroughly familiar with the target device’s functions and use methods and to be knowledgeable about debugging. ...
Page 9
... The related documents (user’s manuals) indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. IE-78K0S-NS IE-78K0S-NS-A IE-789046-NS-EM1 ID78K0-NS, ID78K0S-NS Integrated Debugger Ver. 2.20 or Later Operation (Windows™ Based) µ PD789046 Subseries µ PD789074 Subseries Caution The documents listed above are subject to change without notice ...
Page 10
... APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE...............................................................43 APPENDIX B CAUTIONS ON DESIGNING TARGET SYSTEM.................................................................45 Cautions on Designing Target System When Debugging µ µ µ µ PD789046 Subseries ................45 B.1 Cautions on Designing Target System When Debugging µ µ µ µ PD789074 Subseries ................47 B.2 8 CONTENTS User’s Manual U14433EJ2V0UM ...
Page 11
... Figure No. 1-1 System Configuration ........................................................................................................................................12 1-2 Basic Hardware Configuration...........................................................................................................................14 2-1 IE-789046-NS-EM1 Part Names .......................................................................................................................17 Connection of Emulation Probe (When Debugging µ PD789046 Subseries).....................................................19 3-1 Connection of Emulation Probe (When Debugging µ PD789074 Subseries).....................................................20 3-2 3-3 External Circuits Used as System Clock Oscillator ...........................................................................................21 3-4 When Using Clock That Is Already Mounted on Emulation Board ....................................................................22 3-5 When Using User-Mounted Clock ...
Page 12
... Basic Specifications.......................................................................................................................................... 15 3-1 Main System Clock Settings ............................................................................................................................. 23 3-2 Subsystem Clock Settings ................................................................................................................................ 28 3-3 Switch and Jumper Settings on IE-78K0S-NS.................................................................................................. 35 3-4 Switch and Jumper Settings on IE-78K0S-NS-A .............................................................................................. 35 A-1 Pin Assignments of NP-44GB, NP-44GB-TQ, and NP-H44GB-TQ .................................................................. 43 A-2 Pin Assignments of NGS-30, NP-36GS, NP-H36GS, and NP-K907 ................................................................ 44 10 LIST OF TABLES Title User’ ...
Page 13
... The IE-789046-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78K/0S Series of 8-bit single-chip microcontrollers. This chapter describes the IE-789046-NS-EM1’s system configuration and basic specifications. • Target devices • µ PD789046 Subseries • ...
Page 14
... System Configuration Figure 1-1 illustrates the IE-789046-NS-EM1’s system configuration. Debugger ID78K0S-NS (sold separately) Interface board IE-70000-98-IF-C (sold separately) IE-78K0S-NS (sold separately) or IE-78K0S-NS-A (sold separately) AC adapter IE-70000-MC-PS-B (sold separately) 12 CHAPTER 1 GENERAL Figure 1-1. System Configuration Note 1 Device file (obtain separately) ...
Page 15
... NP-36GS: For 30-pin plastic shrink SOP (MA type) NP-H36GS: Long type for 30-pin plastic shrink SOP (MA type) 3. The conversion socket/conversion adapter is as follows. (1) For µ PD789046 Subseries EV-9200G-44: For 44-pin plastic QFP (GB-8ES type) TGB-044SAP: For 44-pin plastic QFP (GB-8ES type) (2) For µ PD789074 Subseries ...
Page 16
... Hardware Configuration Figure 1-2 shows the IE-789046-NS-EM1’s position in the basic hardware configuration. Figure 1-2. Basic Hardware Configuration Dedicated bus interface Interface board Host machine (sold separately) Interface card (sold separately) 14 CHAPTER 1 GENERAL IE system IE-78K0S-NS (sold separately) or IE-78K0S-NS-A (sold separately) ...
Page 17
... Basic Specifications The IE-789046-NS-EM1’s basic specifications are listed in Table 1-1. Parameter Target device System clock Main clock supply Subsystem clock supply ( µ PD789046 Subseries only) Low-voltage support CHAPTER 1 GENERAL Table 1-1. Basic Specifications Description µ PD789046 Subseries, µ PD789074 Subseries 1 ...
Page 18
... This chapter introduces the parts of the IE-789046-NS-EM1 main unit. The packing box contains the emulation board (IE-789046-NS-EM1), packing list, user’s manual, and guarantee card. If there are any missing or damaged items, please contact an NEC sales representative. Fill out and return the guarantee card that comes with the main unit. ...
Page 19
... Parts of Main Unit Figure 2-1. IE-789046-NS-EM1 Part Names X1 UMCLK socket XTC1 XTC1 XT1 USCLK socket CHAPTER 2 PART NAMES 3 1 User’s Manual U14433EJ2V0UM GND TP1 Low Volt EXTOUT (CP7) EXTIN (CP9) Probe connector CN1 44GB LED1 17 ...
Page 20
... This chapter describes methods for connecting the IE-789046-NS-EM1 to the IE-78K0S-NS or IE-78K0S-NS-A, emulation probe, etc. Mode setting methods are also described. Caution Connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the IE system and the target system has been switched OFF ...
Page 21
... Connection with emulation probe (when debugging µ µ µ µ PD789046 Subseries) See the IE-78K0S-NS User’s Manual (U13549E) or IE-78K0S-NS-A User’s Manual (U15207E) for a description of how to connect an emulation probe to the IE-789046-NS-EM1 when debugging the µ PD789046 Subseries. On this board, connect the emulation probe to CN1. ...
Page 22
... Figure 3-2. Connection of Emulation Probe (When Debugging µ µ µ µ PD789074 Subseries) Not used Main board (IE-78K0S-NS or IE-78K0S-NS-A) 20 CHAPTER 3 INSTALLATION CN3 CN1 Emulation board (IE-789046-NS-EM1) User’s Manual U14433EJ2V0UM Emulation probe (sold separately) CN1 Probe conversion board NP-K907 (sold separately) ...
Page 23
... If the target system includes an external clock, select (1) clock that is already mounted on emulation board, (2) clock that is mounted by user, or (3) pulse input from target system. For the external clock, a clock signal is supplied from outside of the target device and the target device’s internal oscillator is not used. An example of the external circuit is shown in part (b) of Figure 3-3. ...
Page 24
... Clock that is mounted by user The user is able to mount any clock supported by the set specifications on the IE-789046-NS-EM1. Mount either the parts board on which the resonator to be used is mounted or an oscillator on the IE-789046-NS-EM1. This method is useful when using a different frequency from that of the premounted clock. ...
Page 25
... CPU’s clock source (this selects the user’s clock). Remark The IE-789046-NS-EM1 is shipped, the settings for “when using clock that is already mounted on emulation board” are preset. ...
Page 26
... Resistor Rx <Steps> <1> Solder the target ceramic resonator or crystal resonator, resistor Rx, capacitor CA, and capacitor CB (all with suitable oscillation frequencies) onto the parts board (as shown below). Figure 3-7. Connections on Parts Board (When Using Main System Clock or User-Mounted Clock) Parts board (X1 UMCLK) ...
Page 27
... Prepare the IE-789046-NS-EM1. <3> Remove the crystal oscillator that is mounted in the IE-789046-NS-EM1’s X1 UMCLK socket. <4> Connect the parts board (from <1> above) to the X1 UMCLK socket from which the crystal oscillator was removed. Check the pin 1 mark to make sure the board is mounted in the correct direction. ...
Page 28
... Prepare the IE-789046-NS-EM1. <2> Remove the crystal oscillator that is mounted in the IE-789046-NS-EM1’s X1 UMCLK socket. <3> Mount the crystal oscillator prepared by the user in the X1 UMCLK socket from which the crystal oscillator was removed in <2> above. Insert the crystal oscillator pin into the socket aligning the pins as shown in the figure below ...
Page 29
... No hardware settings are required for this situation. When starting the integrated debugger (ID78K0S-NS), open the configuration dialog box and select “External” in the area (Clock) for selecting the CPU’s clock source (this selects the user’s clock). CHAPTER 3 INSTALLATION IE-78K0S-NS or IE-78K0S-NS-A side (Emulation device 4.7 kΩ ...
Page 30
... When the IE-789046-NS-EM1 is shipped, a 32.768 kHz crystal resonator (XTC1) and the parts board (XT1 USCLK) on which pins 6 and 8 are shortened are already mounted on the IE-789046-NS-EM1. Short pins 2 and 3 on the IE-789046-NS-EM1’s jumper (JP1). There is no need to make any other settings via the integrated debugger (ID78K0S-NS) ...
Page 31
Figure 3-10. Connections on Parts Board (When Using Subsystem Clock or User-Mounted Clock) Parts board (XT1 USCLK Remark The sections enclosed in broken ...
Page 32
... Prepare the IE-789046-NS-EM1. <3> Remove the parts board that is mounted in the IE-789046-NS-EM1’s XT1 USCLK socket. <4> Connect the parts board (from <1> above) to the XT1 USCLK socket from which the parts board was removed (see <3> above). Check the pin 1 mark to make sure the board is mounted in the correct direction. ...
Page 33
... Prepare the IE-789046-NS-EM1. <2> Remove the parts board that is mounted in the IE-789046-NS-EM1’s XT1 USCLK socket. <3> Mount the crystal oscillator prepared by the user in the XT1 USCLK socket from which the parts board was removed in <2> above. Insert the crystal oscillator into the socket aligning the pins as shown below. ...
Page 34
... V Parts board 14 Crystal oscillator 7 100 Ω XT1 1 MΩ (3) When using an external clock Short pins 1 and 2 on the IE-789046-NS-EM1’s jumper (JP1). There is no need to make any settings via the integrated debugger (ID78K0S-NS). 32 CHAPTER 3 INSTALLATION IE-78K0S-NS or IE-78K0S-NS-A side (Emulation device 4.7 kΩ ...
Page 35
... When debugging with a voltage that is the same level as that of the target system, supply the same voltage as that of the target system to the TP1 terminal pin of the IE-789046-NS-EM1 (the same applies when the voltage is 5 V). Set the target voltage to between 1.8 and 5.0 V. ...
Page 36
... See the ID78K0-NS, ID78K0S-NS Integrated Debugger Ver. 2.20 or Later Operation User’s Manual (U14910E) for use methods. (1) EXTOUT Output a low level from the EXTOUT pin on the IE-789046-NS-EM1 for 1.3 µ s upon the occurrence of a break event. Caution Connect a pull-up resistor on the target system since this is an open-drain output. ...
Page 37
... Caution Incorrect settings may damage the IE-78K0S-NS. (2) Switch and jumper settings on the IE-78K0S-NS-A When using the IE-789046-NS-EM1, set the switches and jumpers on the IE-78K0S-NS-A as shown in Table 3-4. For details of these switch and jumper settings, refer to the IE-78K0S-NS-A User’s Manual (U15207E). ...
Page 38
... PD789046 Subseries 4.1 When debugging the µ PD789046 Subseries, connect the target system to IE-789046-NS-EM1 via the emulation probe. (1) Signals directly input/output to/from the emulation CPU ...
Page 39
... The emulation CPU operates on the internal power supply voltage (5 V) when the target system is not connected. When the target system is connected, power is supplied via the power supply pin (TP1). The V and V pins of the target system are only used to control the LED1 in the IE-789046-NS-EM1 that monitors DD1 the input of the target system’s power supply (TV • ...
Page 40
... LV CC 4.7 kΩ X1 HC157 LV CC µ PD789009 HSK120 1 MΩ 4.7 kΩ XT1 JP1 HC04 LV CC µ 1 MΩ PD789009 HSK120 User’s Manual U14433EJ2V0UM IE system side Port 0 Port 1 Port 2 Port 3 Port 4.7 kΩ RESET X1 µ PD789009 XT1 µ PD789009 ...
Page 41
... CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS Figure 4-2. Equivalent Circuit 2 of Emulation Circuit Probe side Filter V DD0 V DD1 22 ΩF X2 XT2 V SS0 V SS1 TEST/V OPEN PP User’s Manual U14433EJ2V0UM IE system side G6H-2F (Relay) Power detection 100 Ω µ PC393 1 MΩ OPEN Emulation device LV CC TEST ...
Page 42
... The emulation CPU operates on the internal power supply voltage (5 V) when the target system is not connected. When the target system is connected, power is supplied via the power supply pin (TP1). The V pin of the target system is only used to control LED1 in the IE-789046-NS-EM1, which monitors the input of the target system’s power supply (TV • ...
Page 43
... Probe side (Emulation probe and probe conversion board) Port 0 100 Ω Port 1 Port 2 Port 3 100 Ω RESET LV 100 Ω X1 HSK120 1 MΩ User’s Manual U14433EJ2V0UM IE system side 1 MΩ 4.7 kΩ HC4066 LV CC 4.7 kΩ X1 HC157 CC µ PD789009 µ PD789009 ...
Page 44
... CHAPTER 4 DIFFERENCES BETWEEN TARGET DEVICES AND TARGET INTERFACE CIRCUITS Figure 4-4. Equivalent Circuit 4 of Emulation Circuit Probe side (Emulation probe and probe conversion board TEST G6H-2F (Relay) 100 Ω µ Filter PC393 − 1 MΩ µ OPEN User’s Manual U14433EJ2V0UM IE system side Power detection OPEN Emulation device TEST/V PP ...
Page 45
APPENDIX A. EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. Pin Assignments of NP-44GB, NP-44GB-TQ, and NP-H44GB-TQ Emulation Probe ...
Page 46
... Table A-2. Pin Assignments of NGS-30, NP-36GS, NP-H36GS, and NP-K907 Device Side of NGS-30 NP-36GS, NP-H36GS Remark The NGS-30, NP-36GS, NP-H36GS, and NP-K907 are products of Naito Densei Machida Mfg. Co., Ltd. 44 CN5 Pin No. of CN1 Pin No. of NP-K907 102 User’s Manual U14433EJ2V0UM CN1 Pin No. of IE-789046-NS-EM1 100 57 102 104 103 ...
Page 47
... Follow the configuration below and consider the shape of parts to be mounted on the target system when designing a system. Figure B-1. Distance Between In-Circuit Emulator and Conversion Socket (1) In-circuit emulator IE-78K0S-NS or IE-78K0S-NS-A Emulation board IE-789046-NS-EM1 CN1 Emulation probe NP-44GB, NP-44GB-TQ NP-H44GB-TQ Note Distance when NP-44GB and NP-44GB-TQ are used. When NP-H44GB-TQ is used, the distance is 370 mm ...
Page 48
... APPENDIX B. CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-2. Connection Condition of Target System (NP-H44GB-TQ) Emulation board IE-789046-NS-EM1 Remarks 1. NP-H44GB- product of Naito Densei Machida Mfg. Co., Ltd. 2. TGB-044SAP is a product of TOKYO ELETECH CORPORATION. 46 Emulation probe NP-H44GB-TQ Conversion adapter TGB-044SAP 40 mm User’s Manual U14433EJ2V0UM 11 mm ...
Page 49
... Follow the configuration below and consider the shape of parts to be mounted on the target system when designing a system. Figure B-3. Distance Between In-Circuit Emulator and Conversion Socket (2) In-circuit emulator IE-78K0S-NS or IE-78K0S-NS-A Emulation board IE-789046-NS-EM1 CN1 Probe conversion board NP-K907 Note Distance when NP-36GS is used. When NP-H36GS is used, the distance is 355 mm. Remark NP-36GS, NP-H36GS, and NGS-30 are products of Naito Densei Machida Mfg ...
Page 50
APPENDIX B. CAUTIONS ON DESIGNING TARGET SYSTEM Figure B-4. Connection Condition of Target System (NP-H36GS) Probe conversion board NP-K907 Remark NP-H36GS and NGS-30 are products of Naito Densei Machida Mfg. Co., Ltd. 48 Emulation probe NP-H36GS 75 mm Target system ...
Page 51
User’s Manual U14433EJ2V0UM 49 ...
Page 52
User’s Manual U14433EJ2V0UM ...
Page 53
... NEC Electronics Shanghai, Ltd. Fax: +86-21-6841-1137 Excellent Good Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation ...