IE-784038-NS-EM1 Renesas Electronics America, IE-784038-NS-EM1 Datasheet
IE-784038-NS-EM1
Specifications of IE-784038-NS-EM1
Related parts for IE-784038-NS-EM1
IE-784038-NS-EM1 Summary of contents
Page 1
... NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com Issued by: Renesas Electronics Corporation (http://www ...
Page 2
... Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “ ...
Page 3
... User’s Manual IE-784038-NS-EM1 Emulation Board Target device PD784038 Subseries Document No. U13760EJ1V0UM00 (1st edition) Date Published May 1999 N CP(K) © 1999 Printed in Japan PD784038Y Subseries ...
Page 4
User’s Manual U13760EJ1V0UM00 ...
Page 5
... PC/ trademark of International Business Machines Corporation. The information in this document is subject to change without notice. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document ...
Page 6
... Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: Device availability • Ordering information • Product release schedule • ...
Page 7
... PD784038 Subseries: PD784038Y Subseries: Target Readers This manual is intended for engineers who will use the IE-784038-NS-EM1 with the IE- 78K4-NS to perform system debugging. Engineers who use this manual are expected to be thoroughly familiar with the target device’s functions and use methods and to be knowledgeable about debugging. ...
Page 8
... This includes the target program and the hardware provided by the user. When defined narrowly, it includes only the hardware. IE system This refers to the combination of the IE-78K4-NS and the IE-784038-NS-EM1. Conventions Data significance: Higher digits on the left and lower digits on the right Note: ...
Page 9
... Basic Specifications.................................................................................................................................. 15 CHAPTER 2 PART NAMES........................................................................................................................17 2.1 Parts of Main Unit ...................................................................................................................................... 18 CHAPTER 3 INSTALLATION .....................................................................................................................19 3.1 Connection ................................................................................................................................................. 20 3.2 Clock Settings............................................................................................................................................ 21 3.2.1 Overview of clock settings ............................................................................................................. 21 3.2.2 Main system clock settings............................................................................................................ 23 3.3 Pin Mask Function Settings...................................................................................................................... 28 3.3.1 Wait (WAIT)/hold (HOLD) mask function....................................................................................... 28 3.3.2 Wait/hold display function.............................................................................................................. 28 3.3.3 NMI interrupt mask function ...
Page 10
... Figure No. .............................................................................................................................. 1-1. System Configuration .................................................................................................................. 1-2. Basic Hardware Configuration 2-1. IE-784038-NS-EM1 Part Names 3-1. Connection of Emulation Probe 3-2. External Circuits Used as System Clock Oscillator 3-3. When Using Clock That Is Already Mounted on Emulation Board 3-4. When Using User-Mounted Clock 3-5. When Using an External Clock 3-6 ...
Page 11
Table No. ................................................................................................................................. 1-1. Basic Specifications ...................................................................................................................... 3-1. Main System Clock Settings 3-2. DIP Switch Setting for Wait (WAIT)/Hold (HOLD) Mask Function 3-3. DIP Switch Setting for Wait/Hold Display Function 3-4. DIP Switch Setting for NMI Interrupt Mask Function A-1. ...
Page 12
User’s Manual U13760EJ1V0UM00 ...
Page 13
... The IE-784038-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78K/IV Series of 16-bit single-chip microcontrollers. This chapter describes the IE-784038-NS-EM1’s system configuration and basic specifications. Target device PD784038 Subseries PD784038Y Subseries CHAPTER 1 GENERAL User’ ...
Page 14
... System Configuration Figure 1-1 illustrates the IE-784038-NS-EM1’s system configuration. Debugger ID78K4-NS (sold separately) Interface board IE-70000-98-IF-C (sold separately) IE-78K4-NS (sold separately) AC adapter IE-70000-MC-PS-B (sold separately) 12 CHAPTER 1 GENERAL Figure 1-1. System Configuration Note 1 Device file (sold separately) Control software Host machine PC-9800 Series or IBM PC/AT™ ...
Page 15
... Notes 1. The device file is as follows, in accordance with the subseries. S DF784038: PD784038, 784038Y Subseries 2. The emulation probe is as follows, in accordance with the package. NP-80GC: 80-pin plastic QFP (GC type) NP-80GK: 80-pin plastic TQFP (GK type) The NP-80GC/GK are products of Naito Densei Machida Mfg. Co., Ltd. ...
Page 16
... Hardware Configuration Figure 1-2 shows the IE-784038-NS-EM1’s position in the basic hardware configuration. Figure 1-2. Basic Hardware Configuration Interface board Host machine (sold separately) Interface card (sold separately) 14 CHAPTER 1 GENERAL Dedicated bus interface IE-78K4-NS (sold separately) 78K4 main board (G-78K4 MAIN Board) ...
Page 17
... Basic Specifications The IE-784038-NS-EM1’s basic specifications are listed in Table 1-1. Parameter Target device System clock Main system clock supply Low-voltage support CHAPTER 1 GENERAL Table 1-1. Basic Specifications Description PD784038, 784038Y Subseries 16.0 MHz External: Input via an emulation probe from the target system ...
Page 18
User’s Manual U13760EJ1V0UM00 ...
Page 19
... This chapter introduces the parts of the IE-784038-NS-EM1 main unit. The packing box contains the emulation board (IE-784038-NS-EM1). If there are any missing or damaged items, please contact an NEC sales representative. Fill out and return the guarantee document that comes with the main unit. ...
Page 20
... Parts of Main Unit Figure 2-1. IE-784038-NS-EM1 Part Names X2 PD784038CLK SW1 DIP switch 18 CHAPTER 2 PART NAMES HOLD LED2 WAIT LED3 User’s Manual U13760EJ1V0UM00 GND TP1 Low Volt EXTIN (CP3) EXTOUT (CP4) Probe connector CN1 80GC/GK USERVDD LED1 ...
Page 21
... This chapter describes methods for connecting the IE-784038-NS-EM1 to the IE-78K4-NS, emulation probe, etc. Mode setting methods are also described. Caution Connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the IE system and the target system has been switched OFF ...
Page 22
... Connection (1) Connection with IE-78K4-NS main unit See the IE-78K4-NS User’s Manual (U13356E) for a description of how to connect the IE-784038-NS-EM1 to the IE-78K4-NS. (2) Connection with emulation probe See the IE-78K4-NS User’s Manual (U13356E) for a description of how to connect an emulation probe to the IE- 784038-NS-EM1 ...
Page 23
... IE-78K4-NS. If the target system includes an external clock, select “(3) External clock”. For an external clock, a clock signal is supplied from outside of the target device and the target device’s internal oscillator is not used. An example of the external circuit is shown in part (b) of Figure 3-2. ...
Page 24
... Clock that is mounted by user The user is able to mount any clock supported by the set specifications on the IE-784038-NS-EM1. First mount the resonator on the parts board, then attach the parts board to the IE-784038-NS-EM1. This method is useful when using a different frequency from that of the pre-mounted clock. ...
Page 25
... CPU’s clock source (this selects the user’s clock). Remark The IE-784038-NS-EM1’s factory settings are those listed above under “when using clock that is already mounted on emulation board”. ...
Page 26
... Resistor Rx <Steps> <1> Solder the target ceramic resonator or crystal resonator, resistor Rx, capacitor CA, and capacitor CB (all with suitable oscillation frequency) onto the supplied parts board (as shown below). Figure 3-6. Connections on Parts Board (When Using Main System Clock or User-Mounted Clock) Parts board (X2) ...
Page 27
... Prepare the IE-784038-NS-EM1. <3> Remove the crystal oscillator that is mounted in the IE-784038-NS-EM1’s socket (the socket marked as X2). <4> Connect the parts board (from <1> above) to the socket (X2) from which the crystal oscillator was removed. Check the pin 1 mark to make sure the board is mounted in the correct direction. ...
Page 28
... Figure 3-7. Crystal Oscillator (When Using Main System Clock or User-Mounted Clock) <Steps> <1> Prepare the IE-784038-NS-EM1. <2> Remove the crystal oscillator that is mounted in the IE-784038-NS-EM1’s socket (the socket marked as X2). <3> Connect the crystal oscillator (from <2> above) to the socket (X2) from which the crystal oscillator was removed ...
Page 29
... No hardware settings are required for this situation. When starting the integrated debugger (ID78K4-NS), open the configuration dialog box and select “External” in the area (Clock) for selecting the CPU’s clock source (this selects the user’s clock). CHAPTER 3 INSTALLATION IE-78K4-NS side (Emulation device) 4 ...
Page 30
... Caution When pin P66 is used as a port pin, unless the DIP switch ( turned OFF the LED may light up. 3.3.3 NMI interrupt mask function By setting switch 1 of the DIP switch (SW1) in the IE-784038-NS-EM1 possible to mask the NMI interrupt, which is the alternate function of the P20 pin. Table 3-4. DIP Switch Setting for NMI Interrupt Mask Function ...
Page 31
... Low-Voltage Emulation Setting Low-voltage emulation is possible in the IE system. When the target system is operating on low voltage, supply the same voltage as the target system to the TP1 terminal pin of the IE-784038-NS-EM1. Set the target voltage between 3 and 5 V. Maximum current consumption of TP1 5 V 300 mA ...
Page 32
... External Trigger To set up an external trigger, connect it to the IE-784038-NS-EM1’s check pin, EXTOUT pin, and EXTIN pin as shown below. See the integrated debugger (ID-78K4-NS) User’s Manual (U12796E) for descriptions of related use methods. Figure 3-9. External Trigger Input Position ...
Page 33
... This chapter describes differences between the target device’s signal lines and the signal lines of the IE-784038- NS-EM1’s target interface circuit. Although the target device is a CMOS circuit, the IE-784038-NS-EM1’s target interface circuit consists of an emulation CPU, TTL, CMOS-IC, and other emulation circuits. ...
Page 34
... P50 to P57 P60 to P67 P70 to P77 ASTB REF1 REF3 ANO0, ANO1 AC125 Leave open User’s Manual U13760EJ1V0UM00 IE system side P00 to P07 P10 to P17 CC P20 P21 to P27 P30 to P37 P40 to P47 P50 to P57 P60 to P67 P70 to P77 ASTB REF1 REF3 ANO0, ANO1 ...
Page 35
... Subseries. Their AC characteristics and DC characteristics are therefore different from PD784038 Subseries, making it necessary to observe a stricter timing design than in the case of PD784038 Subseries. RESET signal Signals related to clock input Figure 4-2. Equivalent Circuit 2 of Emulation Circuit Probe side LV CC RESET 22 IE-784038-NS-EM1 X2 mounted clock X1 Target probe X1 pin D HSK120 X2 (3) Other signals ...
Page 36
User’s Manual U13760EJ1V0UM00 ...
Page 37
APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. NP-80GC/GK Pin Assignments (1/2) Emulation Probe ...
Page 38
APPENDIX A EMULATION PROBE PIN ASSIGNMENT TABLE Table A-1. NP-80GC/GK Pin Assignments (2/2) Emulation Probe Remarks 1. The NP-80GC/GK are products of Naito Densei Machida Mfg. Co., Ltd. 2. The numbers in the ...
Page 39
User’s Manual U13760EJ1V0UM00 37 ...
Page 40
User’s Manual U13760EJ1V0UM00 ...
Page 41
... NEC Electronics Taiwan Ltd. Fax: 02-2719-5951 Excellent Good Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation ...