R0E5212DACPE00 Renesas Electronics America, R0E5212DACPE00 Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/5/560/renesas_electronics_america_sml.jpg)
R0E5212DACPE00
Manufacturer Part Number
R0E5212DACPE00
Description
EMULATOR DEV COMPACT R8C-2C/D
Manufacturer
Renesas Electronics America
Type
In Circuit Debuggerr
Datasheet
1.R0E5212DACPE00.pdf
(94 pages)
Specifications of R0E5212DACPE00
Contents
Compact Emulator, IDE, Assembler and Linker
For Use With/related Products
R8C/2C, R8C/2D
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
R0E521000CPE00 User’s Manual
1.3 Specifications
Tables 1.5 and Table 1.6 list the specifications of the R0E521000CPE00.
Table 1.5 R0E521000CPE00 specifications (1)
*1: If using this product when the voltage is less than 2.7V, the JP1 of the R0E521000EPBM0 should be set to EXT.
*2: The hardware break function and trace point settings of the realtime trace function cannot be used at the same time.
REJ10J0845-0600 Rev.6.00 Aug. 20, 2009
Page 18 of 92
Applicable MCUs
Usable mode
Maximum ROM/RAM capacity
Maximum operating frequency
Applicable power supply
Basic debugging functions
Real-time trace function
Real-time RAM monitor function
Hardware break function
Execution time measurement function
Connection to user system
(see “2.9 Connecting the User System”
on page 37)
For details, refer to “2.3.3 Setting the POWER Selection Jumper” (page 24).
R8C Family MCUs
Single-chip mode
ROM capacity: 112KB (04000h--1FFFFh) + 4KB (02000h--02FFFh)
RAM capacity: 8KB (00300h--012FFh, 03000h--03FFFh)
20 MHz at 3.0--5.5 V
10 MHz at 2.7--5.5 V
5 MHz at 2.2--5.5 V
User system connected
(JP1 of the M30290T2-CPEA=EXT)
User system not connected
(JP1 of the M30290T2-CPEA=INT)
- Download
- Software break (max. 64 points)
- Program execution/stop (allows free-run execution supporting software breaks)
- Memory reference/setting (reference/setting C-variables, run-time execution)
- Register reference/setting
- Disassemble display
- C-level debugging, etc.
- 64K-cycle bus information recordable
- 5 trace modes supported (Break/Before/About/After/Full)
- Can be recorded ON/OFF by events
- 1,024 bytes (256 bytes x4)
- Data/last access result
2 points (Address match, bus match, max. 255 pass counts)
Time between program start and stop
For 32-pin 0.8mm pitch LQFP (PLQP0032GB-A):
R0E521134CFG00 (included with the R0E521134CPE00)
R0E521276CFG00 (included with the R0E521276CPE00)
R0E5212L4CFG00 (included with the R0E5212L4CPE00)
For 20-pin 0.65mm pitch LSSOP (PLSP0020JB-A): R0E521174CSJ00
(included with the R0E521174CPE00)
For 20-pin 1.778mm pitch SDIP (PRDP0020BA-A): R0E521174CDB00
(included with the R0E521174CPE10)
For 48-pin 0.5mm pitch LQFP (PLQP0048KB-A): R0E521237CFK00
(included with the R0E521237CPE00)
For 52-pin 0.65mm pitch LQFP (PLQP0052JA-A): R0E521258CFJ00
(included with the R0E521258CPE00)
For 64-pin 0.8mm pitch LQFP (PLQP0064GA-A): R0E5212BACFG00
(included with the R0E5212BACPE00)
For 64-pin 0.5mm pitch LQFP (PLQP0064KB-A): R0E5212BACFK00
(included with the R0E5212BACPE10)
For 80-pin 0.5mm pitch LQFP (PLQP0080KB-A): R0E5212DACFK00
(included with the R0E5212DACPE00)
(Address: 20 bits, Data: 16 bits, MCU status: 12 bits)
2.2--5.5 V
(supplied from the user system)
3.3 V or 5.0 V
(supplied from the emulator, depends on
JP2 of the M30290T2-CPEA)
*1
*2
1. Outline