M30260T2-CPE-GP Renesas Electronics America, M30260T2-CPE-GP Datasheet - Page 76
M30260T2-CPE-GP
Manufacturer Part Number
M30260T2-CPE-GP
Description
DEV COMPACT EMULATOR M16C/26A,28
Manufacturer
Renesas Electronics America
Type
In Circuit Debuggerr
Datasheet
1.M30290T2-CPE.pdf
(88 pages)
Specifications of M30260T2-CPE-GP
Contents
Compact Emulator, IDE, Assembler and Linker
For Use With/related Products
M16C/26A
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 76 of 88
- Download datasheet (2Mb)
M30290T2-CPE User’s Manual
4.5 Notes on Using This Product
Notes on using this product are listed below. When debugging the MCU using this product, be careful about the following
precautions.
REJ10J0494-0200 Rev.2.00 July 16, 2005
Notes on the Self-check:
Note on Quitting the Emulator Debugger:
Notes on the User System (Power Supply, Order of Powering On):
If the self-check does not result normally (excluding target status errors), the emulator may be damaged. Then
contact your local distributor.
Run the self-check with the user system not connected.
To restart the emulator debugger, always shut power to the emulator module off once and then on again.
When the user system is connected, be sure to set the JP1 of the emulator to "EXT".
This emulator cannot supply the power to the user system. Therefore design your system so that the user system
is powered separately.
This emulator consumes max. 500 mA of electric current from the user system.
The voltage of the user system should be as follows.
Do not change the voltage of the user system after turning on the power.
Before powering on your emulator system, check that the host machine, the emulator, the converter board and
user system are all connected correctly. Next, turn on the power to each equipment following the procedure
below.
(1) Turn ON/OFF the user system and the emulator as simultaneously as possible.
(2) When the emulator debugger starts up, check the target status LEDs on the emulator to see if this product
is ready to operate.
Is the power supplied? Check that target status LED (POWER) is ON.*1
Is the clock supplied?
*1 When the user system is not connected the target status LED (POWER) does not light.
2.7 V ≤ Vcc ≤ 5.5 V
Check that target status LED (CLOCK) is ON.
IMPORTANT
4. Hardware Specifications
Page 74 of 86
Related parts for M30260T2-CPE-GP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT STARTER FOR M16C/29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/2D
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
R0K33062P STARTER KIT
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/23 E8A
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C/25
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER H8S2456 SHARPE DSPLY
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C38C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8C35C
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R8CL3AC+LCD APPS
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR RX610
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR R32C/118
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV RSK-R8C/26-29
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR SH7124
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT STARTER FOR H8SX/1622
Manufacturer:
Renesas Electronics America
Datasheet:
Part Number:
Description:
KIT DEV FOR SH7203
Manufacturer:
Renesas Electronics America
Datasheet: