Z86CCP01ZEM Zilog, Z86CCP01ZEM Datasheet
![Z8 EMULATOR/PROGRAMMER BOARD](/photos/9/27/92755/z86ccp01zem_sml.jpg)
Z86CCP01ZEM
Specifications of Z86CCP01ZEM
Z86CCP00ZEM
Related parts for Z86CCP01ZEM
Z86CCP01ZEM Summary of contents
Page 1
... With optional, separately purchased accessory kit (Z86CCP00ZAC) and adapter (Z86E4001ZDV) from Zilog. 14. With optional, separately purchased adapter (Z86E4400ZDV) from Zilog. 15. With optional, separately purchased accessory kit (Z86CCP00ZAC) and adapter (Z86E4001ZDF) from Zilog. 16. With optional, separately purchased adapter (Z86E4400ZDF) from Zilog. CP97Z8X5301 C USTOMER Z86CCP01ZEM ® Z8 CCP Emulation Z86C02/03/04/06/08/16 Z86E02/03/04/06/08 ...
Page 2
... Also included is a full-fea- tured macro cross assembler to enhance programmer pro- ductivity, when used in conjunction with the CCP Emula- tor. The Z8 CCP Emulator (Z86CCP01ZEM member of Zilog's ICEBOX™ product family of in-circuit emulators providing support for the Consumer Controller Processor (CCP TM ) microcontrollers ...
Page 3
... High-Density (HD) Floppy Disk Drive RS-232C COM Port Mouse or Pointing Device Microsoft Windows 3.1 ZMASM REQUIREMENTS If using the optional Zilog Macro Cross Assembler, the following table lists the host computer requirements for it: Table 1-1. Minimum and Recommended System Requirements Windows 3.1 Minimum Recommended Minimum Processor ...
Page 4
... DIP Target Cable DB25 RS-232C Cable Power Cable with Banana Plugs 9VDC Wall Adapter Power Supply Z86C30 Accessory Kit (Z86C3000ZAC) (Not included with Z86CCP01ZEM) 28-Pin PLCC/SOIC-to-Dip Programming Adapter 28-Pin PLCC Emulation Pod Z86C40 44 PLCC Emulation Pod (Z86C4001ZDV) 44-Pin PLCC Emulation Pod ...
Page 5
... The maximum usable rate is determined by the user’s tolerance of the frequency of communication errors. 6. The initial blue Zilog screen can be distorted by other active windows. This only affects the appearance, not the functionality, of the GUI not put a breakpoint at addresses after STOP instruction ...
Page 6
... PCON register) must be set to state “1” on the emulator. 19. When interrupts are enabled, breakpointing after a Halt instruction, the emulator will break at the first instruction in the interrupt service routine that is serviced when an interrupt occurs. 20. Port 0, Port 1, and Port 2 have auto latches permanently enabled. Zilog Z86C50 CP97Z8X5301 ...
Page 7
... Zilog 21. SCLK/16 Mode of SMR register is not supported. Z86C03/C06/C16 1. Devices with the comparator output feature have the P32 comparator output coming out of P35. 2. The register %F8(P01M register) bits D4 and D3 must be set to state “0” and bit D2 must be set to state “1”. 3. WDT Register (F) %0F can only be written in the first 60 internal system clocks from the start of program execution ...
Page 8
... Z8® CCP™ In-Circuit Emulator © 1998 by Zilog, Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Zilog, Inc. The information in this document is subject to change without notice. Devices sold by Zilog, Inc. are covered by warranty and patent indemnification provisions appearing in Zilog, Inc ...