DEMO9S08SH8 Freescale Semiconductor, DEMO9S08SH8 Datasheet

DEMO9S08SH8

Manufacturer Part Number

DEMO9S08SH8

Description

BOARD DEMO FOR MC9S08SH FAM

Manufacturer

Freescale Semiconductor

Type

MCUr

Datasheets

1.DEMO9S08SH8.pdf (14 pages)

2.DEMO9S08SH8.pdf (2 pages)

Specifications of DEMO9S08SH8

Contents

Board, Cable, CD

Processor To Be Evaluated

MC9S08SH4 and MC9S08SH8

Data Bus Width

8 bit

Interface Type

RS-232, USB

Silicon Manufacturer

Freescale

Core Architecture

HCS08

Core Sub-architecture

HCS08

Silicon Core Number

MC9S08

Silicon Family Name

S08SH

Kit Contents

Board

Rohs Compliant

Yes

For Use With/related Products

MC9S08SH4, MC9S08SH8

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (26Kb)

D E M O 9 S 0 8 S H 8 / S G 8

D O C - 0 3 9 8 - 0 2 0

Q U I C K

S T A R T

G U I D E

R E V

1 . 0

0 4 / 2 0 0 7

DEMO9S08SH8/SG8 QUICK START GUIDE

Introduction and Default Settings

This quick start guide will illustrate how to connect the target board to a PC, install the correct version of Code-

Warrior Development Studio, and execute a simple demonstration program loaded in FLASH memory. This quick

start guide applies equally regardless of whether a MC9S08SH8 or MC9S08SG8 is installed on the board.

Please check either the Freescale Semiconductor web site (www.freescale.com) or the Axiom Manufacturing web

site (www.axman.com) for the latest documentation.

Figure 1: DEMO9S08SH8/SG8 Default Settings

Install CodeWarrior Development Studio for HC(S)08 Special Edition

To install CodeWarrior Development Studio for HC(S)08 Special Edition, refer to the “CodeWarrior Development

Studio” DVD case and follow the steps in the included Quick Start Guide.

CodeWarrior Development Studios must be properly installed before attempting to connect the target board to the

host PC. Otherwise, the necessary USB drivers will not be available and the target board will not be recognized

when connected to the host PC.

Run the demo program

The DEMO9S08SH8/SG8 ships with a simple demonstration program preloaded into on-chip FLASH memory.

The assembly source code (SH8_CE.asm) for this demo program is located on the Axiom Support CD in the

/Examples folder. The source code is contained in the SH8/SG8_Demo.zip file.

1. Verify the configuration jumpers are set to the default position. Refer to Figure 1 above.

2. Connect the included USB cable to an open USB port on the host PC and to the USB connector on the target

board.

3. Follow the on-screen instructions to install the necessary USB drivers.

4. After the USB drivers are properly installed, the USB, POWER OUT, and +5V LED’s will be ON.

5. LED1 will toggle at approximately 4Hz. LED2 will toggle state each time SW2 is pressed.

Spencer Ruggles

Related parts for DEMO9S08SH8

DEMO9S08SH8 Summary of contents

Page 1

... PC. Run the demo program The DEMO9S08SH8/SG8 ships with a simple demonstration program preloaded into on-chip FLASH memory. The assembly source code (SH8_CE.asm) for this demo program is located on the Axiom Support CD in the /Examples folder. The source code is contained in the SH8/SG8_Demo.zip file. ...

Page 2

Connect a serial cable (not supplied open ...

Related keywords

demo9s08sh
demo9s08sg8
demo9s08sg32
demo9s12xsfame
demo9s12xep100
demo9s12xdt512
demo9s12ne64
demo9s08sv16
demo9s08se
demo9s08sc4
demo9s08ll16
DEMO9S08SH8 datasheet
DEMO9S08SH8 data sheet
DEMO9S08SH8 pdf datasheet
DEMO9S08SH8 component
DEMO9S08SH8 part
DEMO9S08SH8 distributor
DEMO9S08SH8 RoHS
DEMO9S08SH8 datasheet download