C8051F310-TB Silicon Laboratories Inc, C8051F310-TB Datasheet
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F310-TB
Specifications of C8051F310-TB
Related parts for C8051F310-TB
C8051F310-TB Summary of contents
Page 1
... Kit Contents The C8051F31x Development Kit contains the following items: • C8051F310 Target Board • C8051Fxxx Development Kit Quick-Start Guide • Silicon Laboratories IDE and Product Information CD-ROM. CD content includes: • Silicon Laboratories Integrated Development Environment (IDE) • Keil 8051 Development Tools (macro assembler, linker, evaluation ‘C’ compiler) • ...
Page 2
C8051F31x-DK 3. Software Setup The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software 8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will auto- matically launch, allowing you to install ...
Page 3
Creating a New Project → 1. Select Project New Project to open a new project and reset all configuration settings to default. → 2. Select File New File to open an editor window. Create your source file(s) and save ...
Page 4
... Port I/O crossbar, configuring a timer for an interrupt routine, initializing the system clock, and configuring a GPIO port. When compiled/assembled and linked this pro- gram flashes the green LED on the C8051F310 target board about five times a second using the interrupt handler with a C8051F310 timer. ...
Page 5
... Target Board The C8051F31x Development Kit includes a target board with a C8051F310 device pre-installed for evaluation and preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using the target board. Refer to Figure 2 for the locations of the various I/O connectors. P1 Power connector (accepts input from VDC unregulated power adapter) ...
Page 6
... Two LEDs are also provided on the target board. The red LED labeled PWR is used to indicate a power connection to the target board. The green LED labeled with a port pin name is connected to the C8051F310’s GPIO pin through headers. Remove the shorting block from the header to disconnect the LED from the port pin. The port pin signal is also routed to a pin on the J1 I/O connector ...
Page 7
... P1.1 6.4. Target Board DEBUG Interface (J4) The DEBUG connector (J4) provides access to the DEBUG (C2) pins of the C8051F310 used to connect the Serial Adapter or the USB Debug Adapter to the target board for in-circuit debugging and Flash programming. Table 3 shows the DEBUG pin definitions. Table 3. DEBUG Connector Pin Descriptions Table 2 ...
Page 8
... Serial Interface (J5) A RS232 transceiver circuit and DB-9 (J5) connector are provided on the target board to facilitate serial connec- tions to UART0 of the C8051F310. The TX, RX, RTS and CTS signals of UART0 may be connected to the DB-9 connector and transceiver by installing shorting blocks on header J3. ...
Page 9
Schematic C8051F31x-DK Rev. 0.6 9 ...
Page 10
C8051F31x- OCUMENT HANGE IST Revision 0.4 to Revision 0.5 Section 1, added USB Debug Adapter and USB Cable. Section 2, changed name from "Hardware Setup" to "Hardware Setup using an EC2 Serial Adapter". Section 2, added 2 ...
Page 11
N : OTES C8051F31x-DK Rev. 0.6 11 ...
Page 12
... Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap- plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. ...