TOOLSTICK360DC Silicon Laboratories Inc, TOOLSTICK360DC Datasheet - Page 13

• Manufacturer Part Number: TOOLSTICK360DC
• Description: DAUGHTER CARD TOOLSTCK C8051F362
• Manufacturer: Silicon Laboratories Inc
• Series: ToolStickr
• Type: MCUr

Specifications of TOOLSTICK360DC

• Contents: Board
• Processor To Be Evaluated: C8051F360
• Interface Type: USB
• Operating Supply Voltage: 2.7 V to 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: C8051F360
• For Use With: 336-1345 - TOOLSTICK BASE ADAPTER336-1182 - ADAPTER USB DEBUG FOR C8051FXXX
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1411

7. Additional Demo Examples
In addition to the F362DC_FeaturesDemo example firmware, the ToolStick download package also includes demo
projects named F362DC_ADC0_TemperatureSensor and F362DC_IDA0_SineWave. The instructions for
running these demos can be found at the top of the source file.
The project and source files for these demos can be found in the C:\SiLabs\MCU\ToolStick\F362DC\Firmware\
folder.
8. Using the C8051F362 Daughter Card as a Development Platform
The prototyping area on the ToolStick C8051F362 daughter card makes it easy to interface to external hardware.
All of the digital I/O pins are available so it possible to create a complete system.
8.1. C8051F362 Pin Connections
It is important to note that if external hardware is being added, some of the existing components on the board can
interfere with the signaling. The following is a list of port pins on the C8051F362 that are connected to other
components:
See the daughter card schematic in Section 10 for more information.
8.2. VREF Capacitor
On the C8051F362 devices, if VREF is generated internally, it is output to port pin P0.0. For VREF stability, it is
highly recommended to place a capacitor on the VREF output pin. On the ToolStick C8051F362 Daughter Card,
there are pads on the board (C5) to populate a 0603 surface mount capacitor. The firmware examples for the
daughter card use VDD as VREF, so no external capacitor on P0.0 is necessary for proper operation.
8.3. C2 Pin Sharing
On the C8051F362, the debug pins, C2CK, and C2D, are shared with the pins /RST and P3.0 respectively. The
daughter card includes the resistors necessary to enable pin sharing which allow the /RST and P3.0 pins to be
used normally while simultaneously debugging the device. See Application Note “AN124: Pin Sharing Techniques
for the C2 Interface” at
9. Information Locations
Example source code is installed by default in the “C:\SiLabs\MCU\ToolStick\F362DC\Firmware” directory during
the ToolStick installation.
Documentation
C:\SiLabs\MCU\ToolStick\Documentation and the C:\SiLabs\MCU\ToolStick\F362DC\Documentation directories.
The installer for the ToolStick software is available at www.silabs.com/toolstick.
P0.1—This pin has a pull-down resistor (R7) to ground so that the IDAC output can be converted to a voltage.
R7 can be safely removed from the daughter card if it is not needed.
P0.4, P0.5—These pins are connected directly to the ToolStick Base Adapter for UART communication.
P0.6, P0.7—These pins are connected directly to the ToolStick Base Adapter’s GPIO pins. By default, these
GPIO pins on the Base Adapter are high-impedance pins so they will not affect any signaling. Configuring these
pins on the Base Adapter to output pin or handshaking pins could affect signaling.
P1.3—This pin is connected to the cathode of the green LED on the daughter card. The LED or the R2 resistor
can be removed to disconnect the LED from the pin.
P1.6—This pin is connected to the output of the potentiometer. The 0 ohm resistor can be removed to
disconnect the potentiometer from the pin.
P2.4—This pin is connected to the P2.4 switch and the R9 pull-up resistor. The switch and R9 can be removed
to disconnect them from the pin.
for
www.silabs.com
the
ToolStick
for more information regarding pin sharing.
kit,
including
Rev. 0.2
this
User’s
ToolStick-F362DC
Guide,
can
be
found
in
the
13