101-1102 Rabbit Semiconductor, 101-1102 Datasheet - Page 87
![no-image](/images/no-image-200.jpg)
101-1102
Manufacturer Part Number
101-1102
Description
KIT DEV RABBIT RCM4100 INTL
Manufacturer
Rabbit Semiconductor
Series
RabbitCore 4000r
Type
MPU Moduler
Datasheet
1.20-101-1093.pdf
(112 pages)
Specifications of 101-1102
Contents
RabbitCore Module, Dev. Board, Cable and Dynamic C® CD-Rom
For Use With/related Products
RCM4100
Lead Free Status / RoHS Status
Vendor undefined / Vendor undefined
B.1.1 Prototyping Board Features
•
•
•
•
•
•
•
•
•
User’s Manual
Power Connection
Note that the 3-pin header is symmetrical, with both outer pins connected to ground and
the center pin connected to the raw V+ input. The cable of the AC adapter provided
with the North American version of the Development Kit is terminated with a header
plug that connects to the 3-pin header in either orientation. The header plug leading to
bare leads provided for overseas customers can be connected to the 3-pin header in
either orientation.
Users providing their own power supply should ensure that it delivers 8–24 V DC at
8 W. The voltage regulators will get warm while in use.
Regulated Power Supply
routed to a 5 V switching voltage regulator, then to a separate 3.3 V linear regulator.
The regulators provide stable power to the RCM4100 series module and the Prototyp-
ing Board.
Power LED
Board.
Reset Switch
RCM4100’s
I/O Switches and LEDs
nected to the PB4 and PB5 pins of the RCM4100 series module and may be read as
inputs by sample applications.
Two LEDs are connected to the PB2 and PB3 pins of the RCM4100 series module, and
may be driven as output indicators by sample applications.
Prototyping Area
of through-hole components. +3.3 V, +5 V, and Ground buses run around the edge of
this area. Several areas for surface-mount devices are also available. (Note that there
are SMT device pads on both top and bottom of the Prototyping Board.) Each SMT pad
is connected to a hole designed to accept a 30 AWG solid wire.
Module Extension Header
module is duplicated at header J2. Developers can solder wires directly into the appro-
priate holes, or, for more flexible development, a 2 × 25 header strip with a 0.1" pitch
can be soldered into place. See Figure B-4 for the header pinouts.
Analog Inputs Header
is duplicated at header J3. Developers can solder wires directly into the appropriate
holes, or, for more flexible development, a 2 × 7 header strip with a 0.1" pitch can be
soldered into place. See Figure B-4 for the header pinouts.
RS-232
ing Board at header J4. A 10-pin 0.1" pitch header strip installed at J4 allows you to
connect a ribbon cable that leads to a standard DE-9 serial connector.
NOTE: The same Prototyping Board is used for several series of RabbitCore modules, and
so the signals at J2 depend on the signals available on the specific RabbitCore module.
—Two 3-wire or one 5-wire RS-232 serial ports are available on the Prototyp-
—The power LED lights whenever power is connected to the Prototyping
/RESET_IN
—A momentary-contact, normally open switch is connected directly to the
—A generous prototyping area has been provided for the installation
—A a 3-pin header is provided for connection to the power supply.
—The complete analog pin set of the RCM4100 series module
pin. Pressing the switch forces a hardware reset of the system.
—Two momentary-contact, normally open switches are con-
—The raw DC voltage provided at the 3-pin header is
—The complete non-analog pin set of the RCM4100 series
83