ISL28148EVAL1Z Intersil, ISL28148EVAL1Z Datasheet - Page 13

• Manufacturer Part Number: ISL28148EVAL1Z
• Description: EVALUATION BOARD FOR ISL28148
• Manufacturer: Intersil

Specifications of ISL28148EVAL1Z

• Channels Per Ic: 1 - Single
• Amplifier Type: General Purpose
• Output Type: Single-Ended, Rail-to-Rail
• Slew Rate: 4 V/µs
• -3db Bandwidth: 13MHz
• Current - Output / Channel: 75mA
• Operating Temperature: -40°C ~ 125°C
• Current - Supply (main Ic): 900µA
• Voltage - Supply, Single/dual (±): 2.4 V ~ 5.5 V, ±1.2 V ~ 2.75 V
• Board Type: Fully Populated
• Utilized Ic / Part: ISL28148
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

0.5V, an external series resistor must be used to ensure the
input currents never exceed 5mA (Figure 39).
Enable/Disable Feature
The ISL28148 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10µA
at room temperature. By disabling the part, multiple
ISL28148 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects
of the feedback resistors of the disabled amplifier must be
considered when multiple amplifier outputs are connected
together. Note that feed-through from the IN+ to IN- pins
occurs on any Mux Amp disabled channel where the input
differential voltage exceeds 0.5V (e.g., active channel
V
implementation is best suited for small signal applications. If
large signals are required, use series IN+ resistors, or large
value R
minimize the impact on the active channel. See “Limitations
of the Differential Input Protection” on page 13 for more
details.The EN pin also has an internal pull-down. If left
open, the EN pin will pull to the negative rail and the device
will be enabled by default. When not used, the EN pin should
either be left floating or connected directly to the V- pin.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non-inverting unity gain
applications the current limiting can be via a series IN+ resistor,
or via a feedback resistor of appropriate value. For other gain
configurations, the series IN+ resistor is the best choice, unless
the feedback (R
sufficiently large to limit the input current to 5mA.
Large differential input voltages can arise from several
sources:
• During open loop (comparator) operation. Used this way,
• When the amplifier is disabled but an input signal is still
• When the slew rate of the input pulse is considerably
OUT
the IN+ and IN- voltages don’t track, so differentials arise.
present. An R
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active
channel V
faster than the op amp’s slew rate. If the V
up with the IN+ signal, a differential voltage results, and
= 1V, while disabled channel V
F
V
, to keep the feed-through current low enough to
IN
FIGURE 39. INPUT CURRENT LIMITING
OUT
F
L
) and gain setting (R
determines the voltage on the IN- terminal.
or R
R
IN
G
to GND keeps the IN- at GND, while
+
-
13
G
R
IN
) resistors are both
L
= GND), so the mux
ISL28148, ISL28248, ISL28448
OUT
V
can’t keep
OUT
Large (>2V) differential input voltages can also cause an
increase in disabled I
Using Only One Channel
If the application does not use all channels, then the user
must configure the unused channel(s) to prevent them from
oscillating. The unused channel(s) will oscillate if the input
and output pins are floating. This will result in higher than
expected supply currents and possible noise injection into
the channel being used. The proper way to prevent this
oscillation is to short the output to the negative input and
ground the positive input (as shown in Figure 40).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in
the circuit board layout. The PC board surface must remain
clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
will reduce surface moisture and provide a humidity barrier,
reducing parasitic resistance on the board. When input
leakage current is a concern, the use of guard rings around
the amplifier inputs will further reduce leakage currents.
Figure 41 shows a guard ring example for a unity gain
amplifier that uses the low impedance amplifier output at the
same voltage as the high impedance input to eliminate
surface leakage. The guard ring does not need to be a
specific width, but it should form a continuous loop around
both inputs. For further reduction of leakage currents,
components can be mounted to the PC board using Teflon
standoff insulators.
.
Current Limiting
These devices have no internal current-limiting circuitry. If
the output is shorted, it is possible to exceed the Absolute
Maximum Rating for output current or power dissipation,
potentially resulting in the destruction of the device.
FIGURE 40. PREVENTING OSCILLATIONS IN UNUSED
FIGURE 41. GUARD RING EXAMPLE FOR UNITY GAIN
visible distortion occurs on the input and output signals. To
avoid this issue, keep the input slew rate below 4.8V/µs, or
use appropriate current limiting resistors.
HIGH IMPEDANCE INPUT
IN
CHANNELS
AMPLIFIER
CC
.
+
-
V+
September 21, 2010
FN6337.4