MAX16839EVKIT+ Maxim Integrated Products, MAX16839EVKIT+ Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX16839EVKIT+
Manufacturer Part Number
MAX16839EVKIT+
Description
KIT EVAL FOR MAX16839
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX16839EVKIT.pdf
(8 pages)
Specifications of MAX16839EVKIT+
Core Chip
MAX16839
No. Of Outputs
3
Output Current
100mA
Dimming Control Type
PWM
Development Tool Type
Hardware / Software - Eval/Demo Board
Mcu Supported Families
MAX16839 Family
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MAX16839 Evaluation Kit
Note: Indicate that you are using the MAX16839 when contacting these component suppliers.
•
•
•
The MAX16839 EV kit is fully assembled and tested.
Follow these steps to verify board operation. Caution:
Do not turn on the power supply until all connections
are completed.
1) Verify that shunts are installed on pins 1-2 of jumpers
2) Verify that shunts are not installed on jumpers
3) Verify that a shunt is installed on jumper JU11
4) Set the power-supply output to 12V and disable the
5) Connect the power-supply ground to the PGND PCB
6) Connect the power-supply positive output to the VIN
7) Connect each HB LED string as follows:
2
Central Semiconductor Corp.
Fairchild Semiconductor
Murata Electronics North America, Inc.
TDK Corp.
JU1, JU2, and JU3 (100mA operation).
JU4–JU10 (independent operation).
(bypass chopper circuit).
output. If the total forward voltage of the HB LED
string is > 6.5V, ensure that the input supply rises in
less than 14Fs, or connect the FLTS output to ground
to disable the turn-off in case of fault feature. The IC
can otherwise latch in fault condition at startup.
pad.
PCB pad.
______________________________________________________________________________________
5V to 40V, 500mA adjustable DC power supply
Three series-connected HB LED strings rated no
less than 100mA and a maximum forward voltage
of 39V
See the LED Load Configuration section for more
information
Channel 1: Connect an HB LED string anode to
the LED1+ PCB pad and the cathode to the LED1-
PCB pad.
Channel 2: Connect an HB LED string anode to
the LED2+ PCB pad and the cathode to the LED2-
PCB pad.
Channel 3: Connect an HB LED string anode to
the LED3+ PCB pad and the cathode to the LED3-
PCB pad.
SUPPLIER
Required Equipment
Quick Start
Procedure
631-435-1110
888-522-5372
770-436-1300
847-803-6100
PHONE
8) Enable the power-supply output.
9) Verify that the attached LEDs are illuminated.
The MAX16839 EV kit demonstrates three separate high-
voltage, single-channel, linear HB LED drivers. Each lin-
ear current driver circuit uses a MAX16839 IC in a 6-pin
TDFN surface-mount package with an exposed pad
for enhanced thermal dissipation. On the EV kit, each
driver circuit is configured to supply an HB LED cur-
rent of 100mA per channel at 5% current accuracy. The
MAX16839 ICs control the HB LED current by maintain-
ing a 203mV (typ) drop across each channel’s external
sense resistors (R1 or R2 for channel 1, R3 or R4 for
channel 2, and R5 or R6 for channel 3). Additionally,
each channel can be reconfigured to provide down to
50mA of current.
The EV kit operates from a 5V to 40V rated power sup-
ply providing up to 300mA and the EV kit can with-
stand a 45V load-dump condition. The input supply is
filtered by common-mode choke L1 and capacitor C1,
while battery-reverse protection is provided by diode
D1. The input supply chopper circuit is comprised of
p-channel MOSFET P1, biasing resistor/diode pair R7/
D2, and switching transistor Q1. See the Chopper-Circuit
Operation section for more information on using the
chopper circuit.
The MAX16839 PWM dimming-control feature can be
evaluated with an independent PWM input on each of
the three channels. Each PWM input accepts a digital
signal up to 10kHz at the DIM1, DIM2, or DIM3 and
GND PCB pads. Additionally, each PWM input functions
as an active-high enable for the corresponding chan-
nel. Multiple EV kits can be cascaded using the FLTS1,
FLTS2, FLTS3, and GND PCB pads and configuring the
proper jumpers. Jumpers JU8, JU9, and JU10 disable
the MAX16839 fault-detection features.
Each MAX16839 IC features an exposed pad that uses
the top-layer and bottom-layer PCB copper as a heat-sink.
For a single-layer design, the top-layer copper would only
be required from a thermal-design perspective. The EV
kit PCB uses 2oz copper for optimum thermal dissipation.
Detailed Description of Hardware
www.centralsemi.com
www.fairchildsemi.com
www.murata-northamerica.com
www.component.tdk.com
Component Suppliers
WEBSITE