MAX16824EVKIT+ Maxim Integrated Products, MAX16824EVKIT+ Datasheet - Page 2

• Manufacturer Part Number: MAX16824EVKIT+
• Description: KIT EVAL FOR MAX16824
• Manufacturer: Maxim Integrated Products

Specifications of MAX16824EVKIT+

• Current - Output / Channel: 100mA
• Outputs And Type: 3, Non-Isolated
• Voltage - Output: 26.3V
• Features: Dimmable
• Voltage - Input: 6.5 ~ 28V
• Utilized Ic / Part: MAX16824
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ABSOLUTE MAXIMUM RATINGS
IN to GND ...............................................................-0.3V to +30V
OUT1, OUT2, OUT3 to GND ..................................-0.3V to +40V
CS1, CS2, CS3, REG to GND...................................-0.3V to +6V
PWM1, PWM2, PWM3 to GND .................................-0.3V to +6V
DIN, CLK, LE, OE, DOUT to GND ............................-0.3V to +6V
Maximum Current into Any Pin
Maximum Current into OUT1, OUT2, OUT3......................160mA
High-Voltage, Three-Channel Linear
High-Brightness LED Drivers
ELECTRICAL CHARACTERISTICS
(V
values are at T
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
Supply Voltage Range
GND Current
LED Current-Sense Accuracy
(Note 2)
Dropout Voltage (Note 3)
Output Current Slew Rate
Output Current Leakage
CURRENT SENSE
Regulated CS_ Voltage
OVERTEMPERATURE PROTECTION
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
+5V REGULATOR (REG)
Output Voltage
REG Output Current
REG Short-Circuit Current
LOGIC INPUT (PWM1, PWM2, PWM3)
PWM_ Input Bias Current
PWM_ Input-Voltage High
PWM_ Input-Voltage Low
PWM_ Turn-On Delay
PWM_ Turn-Off Delay
(except OUT1, OUT2, OUT3) ........................................±20mA
IN
_______________________________________________________________________________________
= 12V, C
PARAMETER
REG
J
= T
= 1μF to GND, I
A
= +25°C.) (Note 1)
REG
SYMBOL
= 0, R
I
REGSC
ΔV
I
V
I
I
V
I
LEAK
PWM
GND
V
REG
V
V
REG
CS_
IN
IH
DO
IL
CS_
= 2Ω from CS_ to GND, T
I
10mA < I
10mA < I
I
I
Current rising, V
V
V
I
4.75V < V
V
V
50% of V
50% of V
OUT1
OUT_
OUT_
REG
PWM1
CS1
REG
PWM1
= 0mA (Note 4)
= V
= 0V (Note 5)
= 100mA (current pulsed)
= 150mA (current pulsed)
= I
= V
= V
OUT2
PWM_
PWM_
OUT_
OUT_
CS2
REG
PWM2
PWM2
= V
= I
< 100mA
< 150mA
to 50% of ΔV
to 50% of ΔV
CONDITIONS
OUT_
CS3
OUT3
= V
= V
Continuous Power Dissipation (T
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PWM3
PWM3
16-Pin TSSOP-EP (derate 18.9mW/°C above +70°C)....1500mW
= 4V
=100mA
J
= T
= 5V
= 0V
OUT_
OUT_
A
= -40°C to +125°C, unless otherwise noted. Typical
MIN
4.75
190
6.5
15
4
4
A
= +70°C)
TYP
0.75
100
200
165
1.2
40
23
5
5
MAX
28.0
2.25
5.25
210
475
150
1.5
0.6
10
90
5
7
1
1
UNITS
mA/μs
mA
mV
mA
mA
μA
°C
°C
μA
ns
ns
%
V
V
V
V
V