LM3445-120VSMEV/NOPB National Semiconductor, LM3445-120VSMEV/NOPB Datasheet

BOARD EVAL LM3445 110V

LM3445-120VSMEV/NOPB

Manufacturer Part Number
LM3445-120VSMEV/NOPB
Description
BOARD EVAL LM3445 110V
Manufacturer
National Semiconductor
Series
PowerWise®r

Specifications of LM3445-120VSMEV/NOPB

Current - Output / Channel
350mA
Outputs And Type
1, Non-Isolated
Features
Dimmable
Voltage - Input
90 ~ 135VAC
Utilized Ic / Part
LM3445
Core Chip
LM3445
Topology
Buck (Step Down)
No. Of Outputs
1
Dimming Control Type
Analog
Development Tool Type
Hardware - Eval/Demo Board
Mcu Supported Families
LM3445 Family
Msl
MSL 1 - Unlimited
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / Rohs Status
Supplier Unconfirmed
Other names
LM3445-120VSMEV

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM3445-120VSMEV/NOPB
Manufacturer:
National Semiconductor
Quantity:
135
© 2009 National Semiconductor Corporation
LM3445 120VAC Small
Evaluation Board
Introduction
The demonstration board included in this shipment converts
90V
nected LED’s at 350 mA average current. The LM3445
switching frequency ranges from about 70 kHz with six series
connected LEDS, to about 110 kHz with thirteen series con-
nected LEDs. The switching frequency can be modified to
optimize performance, please refer to the LM3445 datasheet
for details. This is a four-layer board using the bottom and top
layer for component placement. The demonstration board
can be modified to adjust the LED forward current, the number
of series connected LEDs and switching frequency. Refer to
the LM3445 datasheet for detailed instructions.
A bill of materials below describes the parts used on this
demonstration board. A schematic and layout have also been
included below along with measured performance character-
Simplified LM3445 Schematic and Efficiency Plot
Warning: The LM3445 evaluation boards have no isolation or any type of protection from shock. Caution must be taken when handling evaluation board.
Warning: This LM3445 evaluation PCB is a non-isolated design. The ground connection on the evaluation board is NOT referenced to earth ground. If an
AC
to 135V
Avoid touching evaluation board, and removing any cables while evaluation board is operating. Isolating the evaluation board rather than the
oscilloscope is highly recommended.
oscilloscope ground lead is connected to the evaluation board ground test point for analysis, and AC power is applied, the fuse (F1) will fail open.
The oscilloscope should be powered via an isolation transformer before an oscilloscope ground lead is connected to the evaluation board.
AC
input, and drives six, to thirteen series con-
300994
30099401
National Semiconductor
Application Note 1978
Matthew Reynolds
November 10, 2009
istics. The above restrictions for the input voltage are valid
only for the demonstration board as shipped with the
schematic below. Please refer to the LM3445 data sheet for
detailed information regarding the LM3445 device, and the
application circuit. The board is currently set up to drive six to
thirteen series connected LEDs, but the evaluation board may
be modified to accept fewer series LEDs. Refer to the LM3445
datasheet for further explanation.
Evalution Board Operating
Conditions
V
Six to thirteen series connected LEDs
I
LED
IN
= 90V
= 350 mA
AC
to 135V
AC
www.national.com
30099402

Related parts for LM3445-120VSMEV/NOPB

LM3445-120VSMEV/NOPB Summary of contents

Page 1

... Warning: This LM3445 evaluation PCB is a non-isolated design. The ground connection on the evaluation board is NOT referenced to earth ground oscilloscope ground lead is connected to the evaluation board ground test point for analysis, and AC power is applied, the fuse (F1) will fail open. ...

Page 2

... Pull above 4.9V (typical) to tri-state DIM. 3 DIM Input/output dual function dim pin. This pin can be driven with an external PWM signal to dim the LEDs. It may also be used as an output signal and connected to the DIM pin of other LM3445 or LED drivers to dim multiple LED circuits simultaneously. 4 COFF OFF time setting pin ...

Page 3

... LM3445 Evaluation Board Schematic 3 30099408 www.national.com ...

Page 4

... Bill of Materials LM3445 Evaluation Board REF DES U1 IC DRIVER LED W/TRIAC DIM 10MSOP BR1 Bridge Rectifier Vr = 400V 0.8A Ceramic .10uF 250V X7R 1210 C2 Ceramic, 0.01uF, X7R, 25V, 10% C3 Ceramic, 1000pF 500V X7R 1206 C4, C5, C12 C6, C10 CAP 33uF 100V ELECT NHG RADIAL ...

Page 5

REF DES Description R20 RES 4.99 OHM 1/8W 1% 0805 R21 RES 12.1 OHM, 0.25W1%, 1206 R22 RES 1.8 OHM 1/3W 5% 1210 R23 RES 499 OHM, 0.25W1%, 1206 RT1 CURRENT LIM INRUSH 60OHM 20% TP10-TP13 Terminal, Turret, TH, Double ...

Page 6

... PCB Layout Warning: The LM3445 evaluation boards have no isolation or any type of protection from shock. Caution must be taken when handling evaluation board. Avoid touching evaluation board, and removing any cables while evaluation board is operating. Isolating the evaluation board rather than the oscilloscope is highly recommended ...

Page 7

Notes 7 www.national.com ...

Page 8

... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...

Related keywords