AD9750-EB Analog Devices Inc, AD9750-EB Datasheet - Page 11

• Manufacturer Part Number: AD9750-EB
• Description: BOARD EVAL FOR AD9750
• Manufacturer: Analog Devices Inc
• Series: TxDAC®r

Specifications of AD9750-EB

• Rohs Status: RoHS non-compliant
• Number Of Dac's: 1
• Number Of Bits: 10
• Outputs And Type: 1, Differential
• Sampling Rate (per Second): 125M
• Data Interface: Parallel
• Settling Time: 35ns
• Dac Type: Current
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9750

and 625 A, respectively. The associated equations in Figure 21
can be used to determine the value of R
ANALOG OUTPUTS
The AD9750 produces two complementary current outputs,
IOUTA and IOUTB, which may be configured for single-end
or differential operation. IOUTA and IOUTB can be converted
into complementary single-ended voltage outputs, V
V
Transfer Function section by Equations 5 through 8. The
differential voltage, V
can also be converted to a single-ended voltage via a transformer
or differential amplifier configuration.
Figure 22 shows the equivalent analog output circuit of the
AD9750 consisting of a parallel combination of PMOS differen-
tial current switches associated with each segmented current
source. The output impedance of IOUTA and IOUTB is deter-
mined by the equivalent parallel combination of the PMOS
switches and is typically 100 k in parallel with 5 pF. Due to
the nature of a PMOS device, the output impedance is also
slightly dependent on the output voltage (i.e., V
and, to a lesser extent, the analog supply voltage, AVDD, and
full-scale current, I
signal dependency can be a source of dc nonlinearity and ac linear-
ity (i.e., distortion), its effects can be limited if certain precau-
tions are noted.
IOUTA and IOUTB also have a negative and positive voltage
compliance range. The negative output compliance range of
–1.0 V is set by the breakdown limits of the CMOS process.
Operation beyond this maximum limit may result in a break-
down of the output stage and affect the reliability of the AD9750.
The positive output compliance range is slightly dependent on
the full-scale output current, I
nominal 1.25 V for an I
2 mA. Operation beyond the positive compliance range will
induce clipping of the output signal which severely degrades
the AD9750’s linearity and distortion performance.
REV. 0
OUTB
, via a load resistor, R
V
1 F
Figure 21. Dual-Supply Gain Control Circuit
GC
Figure 22. Equivalent Analog Output
R
SET
OUTFS
I
I
WITH V
DIFF
REF
REF
OUTFS
. Although the output impedance’s
= (1.2–V
, existing between V
GC
REFIO
FS ADJ
AD9750
+1.2V REF
= 20 mA to 1.00 V for an I
< V
LOAD
OUTFS
GC
REFIO
REFLO
)/R
IOUTA
R
, as described in the DAC
SET
LOAD
AND 62.5 A
. It degrades slightly from its
150pF
SET
.
AVDD
R
OUTA
IOUTB
LOAD
I
CURRENT
OUTA
REF
SOURCE
ARRAY
AVDD
AVDD
and V
625A
and V
OUTA
OUTFS
OUTB
OUTB
and
=
)
–11–
For applications requiring the optimum dc linearity, IOUTA
and/or IOUTB should be maintained at a virtual ground via an
I-V op amp configuration. Maintaining IOUTA and/or IOUTB
at a virtual ground keeps the output impedance of the AD9750
fixed, significantly reducing its effect on linearity. However,
it does not necessarily lead to the optimum distortion perfor-
mance due to limitations of the I-V op amp. Note that the
INL/DNL specifications for the AD9750 are measured in
this manner using IOUTA. In addition, these dc linearity
specifications remain virtually unaffected over the specified
power supply range of 4.5 V to 5.5 V.
Operating the AD9750 with reduced voltage output swings at
IOUTA and IOUTB in a differential or single-ended output
configuration reduces the signal dependency of its output
impedance thus enhancing distortion performance. Although
the voltage compliance range of IOUTA and IOUTB extends
from –1.0 V to +1.25 V, optimum distortion performance is
achieved when the maximum full-scale signal at IOUTA and
IOUTB does not exceed approximately 0.5 V. A properly se-
lected transformer with a grounded center-tap will allow the
AD9750 to provide the required power and voltage levels to
different loads while maintaining reduced voltage swings at
IOUTA and IOUTB. DC-coupled applications requiring a
differential or single-ended output configuration should size
R
examples of various output configurations.
The most significant improvement in the AD9750’s distortion
and noise performance is realized using a differential output
configuration. The common-mode error sources of both IOUTA
and IOUTB can be substantially reduced by the common-mode
rejection of a transformer or differential amplifier. These
common-mode error sources include even-order distortion
products and noise. The enhancement in distortion performance
becomes more significant as the reconstructed wave-form’s
frequency content increases and/or its amplitude decreases.
The distortion and noise performance of the AD9750 is also
slightly dependent on the analog and digital supply as well as the
full-scale current setting, I
5.0 V ensures maximum headroom for its internal PMOS current
sources and differential switches leading to improved distortion
performance. Although I
20 mA, selecting an I
tortion and noise performance also shown in Figure 8. The
noise performance of the AD9750 is affected by the digital sup-
ply (DVDD), output frequency, and increases with increasing
clock rate as shown in Figure 11. Operating the AD9750 with
low voltage logic levels between 3 V and 3.3 V will slightly re-
duce the amount of on-chip digital noise.
In summary, the AD9750 achieves the optimum distortion and
noise performance under the following conditions:
(1) Differential Operation.
(2) Positive voltage swing at IOUTA and IOUTB limited to
(3) I
(4) Analog Supply (AVDD) set at 5.0 V.
(5) Digital Supply (DVDD) set at 3.0 V to 3.3 V with appro-
Note that the ac performance of the AD9750 is characterized
under the above mentioned operating conditions.
LOAD
+0.5 V.
priate logic levels.
OUTFS
accordingly. Refer to Applying the AD9750 section for
set to 20 mA.
OUTFS
OUTFS
OUTFS
of 20 mA will provide the best dis-
. Operating the analog supply at
can be set between 2 mA and
AD9750