MAX17000EVKIT+ Maxim Integrated Products, MAX17000EVKIT+ Datasheet - Page 2

• Manufacturer Part Number: MAX17000EVKIT+
• Description: KIT EVAL FOR MAX17000
• Manufacturer: Maxim Integrated Products

Specifications of MAX17000EVKIT+

• Main Purpose: Special Purpose DC/DC, DDR Memory Supply
• Outputs And Type: 3, Non-Isolated
• Power - Output: 19.8W
• Voltage - Output: 1.8V, 0.9V, 0.9V
• Current - Output: 10A, 2A, 3mA
• Voltage - Input: 7 ~ 20V
• Regulator Topology: Buck
• Frequency - Switching: 300kHz
• Board Type: Fully Populated
• Utilized Ic / Part: MAX17000
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX17000 Evaluation Kit
Note: Indicate that you are using the MAX17000 when contacting these component suppliers.
2
Fairchild Semiconductor
Murata Electronics North America, Inc.
NEC TOKIN Corp.
Panasonic Corp.
SANYO Electric Co., Ltd.
Sumida Corp.
TDK Corp.
Vishay
Würth Electronik GmbH & Co. KG
DESIGNATION
PGOOD1,
_______________________________________________________________________________________
PGOOD2
R14–R20
TP1, TP2
R9–R12,
R2, R3
R4–R7
R13
N1
N2
N3
R1
R8
U1
—
—
Component List (continued)
QTY
1
1
0
0
1
2
4
1
0
1
2
1
6
1
SUPPLIER
30V, 20A n-channel MOSFET
(PowerPAK 8 SO)
Fairchild FDMS8690
30V, 40A n-channel MOSFET
(PowerPAK 8 SO)
Fairchild FDMS8660S
Not installed, dual MOSFET (8 SO)
Fairchild FDS6982S
Not installed, test points
0.002Ω ±1%, 1/2 W current-sense
resistor (2010)
Vishay WSL20102L000FEA
1kΩ ±5% resistors (0603)
100kΩ ±5% resistors (0603)
200kΩ ±1% resistor (0603)
Not installed, resistors (0603)
R9–R12 are shorted by PC trace;
R14–R20 are open
10Ω ±5% resistor (0603)
Test points
DDR memory power solution
(24 TQFN)
Maxim MAX17000ETG+
Shunts, 0.1in centers
PCB: MAX17000 Evaluation Kit+
DESCRIPTION
888-522-5372
770-436-1300
408-324-1790
800-344-2112
619-661-6835
847-545-6700
847-803-6100
402-563-6866
201-785-8800
PHONE
Before beginning, the following equipment is needed:
•
•
•
The MAX17000 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supplies until all
connections are completed.
1) Verify that the jumpers follow the default settings in
2) Connect the positive terminal of the VDD power
3) Connect the positive terminal of the IN power sup-
4) Set the IN power supply to 12V.
5) Set the VDD power supply to 5V.
6) Turn on the IN power supply before turning on the
7) Verify that the VDDQ output (OUT) is approximately
8) Verify that the termination power-supply output
9) Verify that the termination reference buffer output
5V, 100mA DC power supply (VDD)
7V to 20V, 5A DC power supply (IN)
Voltmeter
Table 1.
supply to the VDD pad. Connect the negative termi-
nal of the VDD power supply to the AGND pad.
ply to the IN pad. Connect the negative terminal of
the IN power supply to the PGND pad.
VDD power supply.
1.8V.
(VTT) is approximately 0.9V.
(VTTR) is approximately 0.9V.
www.fairchildsemi.com
www.murata-northamerica.com
www.nec-tokinamerica.com
www.panasonic.com
www.sanyodevice.com
www.sumida.com
www.component.tdk.com
www.vishay.com
www.we-online.com
Component Suppliers
Recommended Equipment
WEBSITE
Quick Start
Procedure