ISL6553EVAL1 Intersil, ISL6553EVAL1 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6553EVAL1
Manufacturer Part Number
ISL6553EVAL1
Description
EVALUATION BOARD ISL6553
Manufacturer
Intersil
Series
Endura™r
Specifications of ISL6553EVAL1
Main Purpose
Special Purpose DC/DC, VRM Supply
Outputs And Type
1, Non-Isolated
Power - Output
45W
Voltage - Output
1.5V
Current - Output
30A
Voltage - Input
5V, 12V
Regulator Topology
Buck
Frequency - Switching
350kHz
Board Type
Fully Populated
Utilized Ic / Part
HIP6601, ISL6553
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Figure 5 shows the regulator operating from an ATX supply.
In this figure, note the slight rise in PGOOD as the 5V supply
rises. The PGOOD output stage is made up of NMOS and
PMOS transistors. On the rising VCC , the PMOS device
becomes active slightly before the NMOS transistor pulls
“down”, generating the slight rise in the PGOOD voltage.
Note that Figure 5 shows the 12V gate driver voltage
available before the 5V supply to the ISL6553 has reached
its threshold level. If conditions were reversed and the 5V
supply was to rise first, the start-up sequence would be
different. In this case the ISL6553 will sense an over-current
condition due to charging the output capacitors. The supply
will then restart and go through the normal Soft-Start cycle.
FIGURE 3. START-UP OF 4 PHASE SYSTEM OPERATING AT
FIGURE 4. START-UP OF 4 PHASE SYSTEM OPERATING AT
DELAY TIME
500kHz
200kHz
DELAY TIME
8
V
IN
V
IN
= 12V
= 12V
PWM 1
OUTPUT
PGOOD
V
5V
VCC
V COMP
PGOOD
V
5V
VCC
CORE
CORE
ISL6553
.
Fault Protection
The ISL6553 protects the microprocessor and the entire
power system from damaging stress levels. Within the
ISL6553 both over-voltage and over-current circuits are
incorporated to protect the load and regulator.
Over-Voltage
The VSEN pin is connected to the microprocessor CORE
voltage. A CORE over-voltage condition is detected when
the VSEN pin goes more than 15% above the programmed
VID level.
The over-voltage condition is latched, disabling normal PWM
operation, and causing PGOOD to go low. The latch can
only be reset by lowering and returning VCC high to initiate a
POR and Soft-Start sequence.
During a latched over-voltage, the PWM outputs will be
driven either low or three state, depending upon the VSEN
input. PWM outputs are driven low when the VSEN pin
detects that the CORE voltage is 15% above the
programmed VID level. This condition drives the PWM
outputs low, resulting in the lower or synchronous rectifier
MOSFETs to conduct and shunt the CORE voltage to
ground to protect the load.
If after this event, the CORE voltage falls below the over-
voltage limit (plus some hysteresis), the PWM outputs will
three state. The HIP6601 family drivers pass the three state
information along, and shuts off both upper and lower
MOSFETs. This prevents “dumping” of the output capacitors
back through the lower MOSFETs, avoiding a possibly
destructive ringing of the capacitors and output inductors. If
the conditions that caused the over-voltage still persist, the
PWM outputs will be cycled between three state and V
clamped to ground, as a hysteretic shunt regulator.
FIGURE 5. SUPPLY POWERED BY ATX SUPPLY
ATX SUPPLY ACTIVATED BY ATX “PS-ON PIN”
V
IN
= 5V, CORE LOAD CURRENT = 31A
FREQUENCY 200kHz
12V ATX
SUPPLY
PGOOD
V
5 V ATX
SUPPLY
CORE
CORE