LM2736X EVAL National Semiconductor, LM2736X EVAL Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM2736X EVAL
Manufacturer Part Number
LM2736X EVAL
Description
BOARD EVALUATION LM2736X
Manufacturer
National Semiconductor
Specifications of LM2736X EVAL
Main Purpose
DC/DC, Step Down
Outputs And Type
1, Non-Isolated
Voltage - Output
1.5V
Current - Output
750mA
Voltage - Input
3 ~ 18V
Regulator Topology
Buck
Frequency - Switching
1.6MHz
Board Type
Fully Populated
Utilized Ic / Part
LM2736
Lead Free Status / RoHS Status
Not applicable / Not applicable
Power - Output
-
Application Information
ENABLE PIN / SHUTDOWN MODE
The LM2736 has a shutdown mode that is controlled by the
enable pin (EN). When a logic low voltage is applied to EN,
the part is in shutdown mode and its quiescent current drops
to typically 30nA. Switch leakage adds another 40nA from
the input supply. The voltage at this pin should never exceed
V
SOFT-START
This function forces V
during start up. During soft-start, the error amplifier’s refer-
ence voltage ramps from 0V to its nominal value of 1.25V in
approximately 200µs. This forces the regulator output to
ramp up in a more linear and controlled fashion, which helps
reduce inrush current.
OUTPUT OVERVOLTAGE PROTECTION
The overvoltage comparator compares the FB pin voltage to
a voltage that is 10% higher than the internal reference Vref.
Once the FB pin voltage goes 10% above the internal refer-
ence, the internal NMOS control switch is turned off, which
allows the output voltage to decrease toward regulation.
UNDERVOLTAGE LOCKOUT
Undervoltage lockout (UVLO) prevents the LM2736 from
operating until the input voltage exceeds 2.74V(typ).
The UVLO threshold has approximately 440mV of hyster-
esis, so the part will operate until V
Hysteresis prevents the part from turning off during power up
if V
CURRENT LIMIT
The LM2736 uses cycle-by-cycle current limiting to protect
the output switch. During each switching cycle, a current limit
comparator detects if the output switch current exceeds 1.5A
(typ), and turns off the switch until the next switching cycle
begins.
IN
FIGURE 5. Boost Voltage Supplied from the Shunt
IN
+ 0.3V.
is non-monotonic.
OUT
Zener on V
to increase at a controlled rate
IN
IN
drops below 2.3V(typ).
(Continued)
20124248
9
THERMAL SHUTDOWN
Thermal shutdown limits total power dissipation by turning
off the output switch when the IC junction temperature ex-
ceeds 165˚C. After thermal shutdown occurs, the output
switch doesn’t turn on until the junction temperature drops to
approximately 150˚C.
Design Guide
INDUCTOR SELECTION
The Duty Cycle (D) can be approximated quickly using the
ratio of output voltage (V
The catch diode (D1) forward voltage drop and the voltage
drop across the internal NMOS must be included to calculate
a more accurate duty cycle. Calculate D by using the follow-
ing formula:
V
The diode forward drop (V
depending on the quality of the diode. The lower V
higher the operating efficiency of the converter.
The inductor value determines the output ripple current.
Lower inductor values decrease the size of the inductor, but
increase the output ripple current. An increase in the inductor
value will decrease the output ripple current. The ratio of
ripple current (∆i
is set between 0.3 and 0.4 at 750mA. The ratio r is defined
as:
One must also ensure that the minimum current limit (1.0A)
is not exceeded, so the peak current in the inductor must be
calculated. The peak current (I
lated by:
If r = 0.7 at an output of 750mA, the peak current in the
inductor will be 1.0125A. The minimum guaranteed current
limit over all operating conditions is 1.0A. One can either
reduce r to 0.6 resulting in a 975mA peak current, or make
the engineering judgement that 12.5mA over will be safe
enough with a 1.5A typical current limit and 6 sigma limits.
When the designed maximum output current is reduced, the
ratio r can be increased. At a current of 0.1A, r can be made
as high as 0.9. The ripple ratio can be increased at lighter
loads because the net ripple is actually quite low, and if r
remains constant the inductor value can be made quite
large. An equation empirically developed for the maximum
ripple ratio at any current below 2A is:
Note that this is just a guideline.
SW
can be approximated by:
L
) to output current (I
r = 0.387 x I
V
SW
I
LPK
O
= I
) to input voltage (V
= I
D
O
) can range from 0.3V to 0.7V
O
x R
LPK
+ ∆I
OUT
DS(ON)
) in the inductor is calcu-
-0.3667
L
/2
O
) is optimized when it
IN
):
www.national.com
D
is, the