LM25575EVAL National Semiconductor, LM25575EVAL Datasheet
LM25575EVAL
Specifications of LM25575EVAL
Related parts for LM25575EVAL
LM25575EVAL Summary of contents
Page 1
... TSSOP-16 package featuring an exposed die attach pad for thermal dissipation. The LM25575 is sup- ported by the full suite of WEBENCH Simplified Application Schematic WEBENCH ® registered trademark of National Semiconductor Corporation. © 2009 National Semiconductor Corporation LM25575/LM25575Q Features ■ LM25575Q is an Automotive Grade product that is AEC- Q100 grade 1 qualified (− ...
Page 2
Connection Diagram Ordering Information Order Number Package Type LM25575MH Exposed Pad TSSOP-16 MXA16A LM25575MHX Exposed Pad TSSOP-16 MXA16A LM25575QMH Exposed Pad TSSOP-16 MXA16A LM25575QMHX Exposed Pad TSSOP-16 MXA16A * Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for ...
Page 3
Pin Descriptions Pin(s) Name 1 VCC Output of the bias regulator 2 SD Shutdown or UVLO input 3 Vin Input supply voltage 4 SYNC Oscillator synchronization input or output The internal oscillator can be synchronized to an external 5 COMP ...
Page 4
Pin(s) Name 16 BST Boost input for bootstrap capacitor NA EP Exposed Pad www.national.com Description An external capacitor is required between the BST and the SW pins. A 0.022µF ceramic capacitor is recommended. The capacitor is charged from Vcc via ...
Page 5
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications GND IN BST to GND PRE to GND SW to GND (Steady State) BST SD GND CC Electrical Characteristics apply over full Operating Junction Temperature range. V Symbol ...
Page 6
Symbol Parameter RAMP GENERATOR Ramp Current 1 Ramp Current 2 PWM COMPARATOR Forced Off-time Min On-time COMP to PWM Comparator Offset ERROR AMPLIFIER Feedback Voltage FB Bias Current DC Gain COMP Sink / Source Current Unity Gain Bandwidth DIODE SENSE ...
Page 7
Soft Start Current vs Temperature 20212122 7kΩ L 20212124 Demoboard Efficiency vs I and V OUT IN 20212126 12V IN Error Amplifier Gain/Phase A = 101 ...
Page 8
Typical Application Circuit and Block Diagram www.national.com 8 ...
Page 9
Detailed Operating Description The LM25575 switching regulator features all of the functions necessary to implement an efficient high voltage buck regu- lator using a minimum of external components. This easy to use regulator integrates a 42V N-Channel buck switch with ...
Page 10
Shutdown / Standby The LM25575 contains a dual level Shutdown (SD) circuit. When the SD pin voltage is below 0.7V, the regulator low current shutdown mode. When the SD pin voltage is greater than 0.7V but less ...
Page 11
FIGURE 5. Simplified Oscillator Block Diagram and SYNC I/O Circuit Error Amplifier and PWM Comparator The internal high gain error amplifier generates an error signal proportional to the difference between the regulated output voltage and an internal precision reference (1.225V). ...
Page 12
The sample & hold DC level illustrated in Figure 6 is derived from a measurement of the re-circulating Schottky diode an- ode current. The re-circulating diode anode should be con- nected to the IS pin. The diode current flows through ...
Page 13
Maximum Duty Cycle / Input Drop- out Voltage There is a forced off-time of 500ns implemented each cycle to guarantee sufficient time for the diode current to be sam- pled. This forced off-time limits the maximum duty cycle of the ...
Page 14
Application Information EXTERNAL COMPONENTS The procedure for calculating the external components is il- lustrated with the following design example. The Bill of Mate- rials for this design is listed in Table 1. The circuit shown in Figure 1 is configured ...
Page 15
RMS current rating and minimum ripple voltage. A good approximation for the re- quired ripple current rating necessary is I Quality ceramic capacitors with a low ESR should be selected for the input filter. To ...
Page 16
R4C5). The error amplifier zero cancels the modulator pole leaving a single pole response at the crossover frequen the loop gain. A single pole response at the crossover frequency yields a very stable loop with 90 ...
Page 17
FIGURE 12. VCC Bias from VOUT for 8V < VOUT < 14V FIGURE 13. VCC Bias with Additional Winding on the Output Inductor 17 20212118 20212119 www.national.com ...
Page 18
PCB LAYOUT AND THERMAL CONSIDERATIONS The circuit in Figure 1 serves as both a block diagram of the LM25575 and a typical application board schematic for the LM25575 buck regulator there are two loops where cur- rents are ...
Page 19
... CAPACITOR, CER, KEMET NOT USED DIODE, 60V, CENTRAL INDUCTOR, COOPER NOT USED NOT USED RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR REGULATOR, NATIONAL SEMICONDUCTOR 19 VALUE 1µ, 100V 1µ, 100V 470p, 100V 0.01µ, 100V 0.01µ, 100V 0.022µ, 100V 0.47µ, 16V 10µ, 16V 120µ ...
Page 20
PCB Layout www.national.com Component Side Solder Side Silkscreen 20 20212129 20212130 20212131 ...
Page 21
Typical Schematic for High Frequency (1MHz) Application 21 20212140 www.national.com ...
Page 22
Physical Dimensions www.national.com inches (millimeters) unless otherwise noted 16-Lead TSSOP Package NS Package Number MXA16A 22 ...
Page 23
Notes 23 www.national.com ...
Page 24
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...