MCP1603EV Microchip Technology, MCP1603EV Datasheet - Page 4
![BOARD EVAL BUCK CONV MCP1603](/photos/9/14/91409/mcp1603ev_sml.jpg)
MCP1603EV
Manufacturer Part Number
MCP1603EV
Description
BOARD EVAL BUCK CONV MCP1603
Manufacturer
Microchip Technology
Type
DC/DC Switching Converters, Regulators & Controllersr
Specifications of MCP1603EV
Main Purpose
DC/DC, Step Down
Outputs And Type
1, Non-Isolated
Voltage - Output
0.8V, 1.2V, 1.8V, 2.5V, or 3.3V
Current - Output
500mA
Voltage - Input
2.7 ~ 5.5V
Regulator Topology
Buck
Frequency - Switching
2MHz
Board Type
Fully Populated
Utilized Ic / Part
MCP1603
Silicon Manufacturer
Microchip
Application Sub Type
Buck Converter
Kit Application Type
Power Management - Voltage Regulator
Silicon Core Number
MCP1603
Input Voltage
2.7 V to 5.5 V
Output Voltage
0.8 V to 3.3 V
Product
Power Management Modules
Kit Contents
Board
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
MCP1603
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
MCP1603
1.0
Absolute Maximum Ratings †
V
All Other I/O ...............................(GND - 0.3V) to (V
L
Output Short Circuit Current..................................Continuous
Power Dissipation (Note 5) ..........................Internally Limited
Storage Temperature.....................................-65°C to +150°C
Ambient Temp. with Power Applied.................-40°C to +85°C
Operating Junction Temperature...................-40°C to +125°C
ESD Protection On All Pins:
DC CHARACTERISTICS
DS22042A-page 4
Electrical Characteristics: Unless otherwise indicated, V
I
Input Characteristics
Input Voltage
Maximum Output Current
Shutdown Current
Quiescent Current
Shutdown/UVLO/Thermal Shutdown Characteristics
SHDN, Logic Input Voltage Low
SHDN, Logic Input Voltage High
SHDN, Input Leakage Current
Undervoltage Lockout
Undervoltage Lockout Hysteresis UVLO
Thermal Shutdown
Thermal Shutdown Hysteresis
Note 1:
X
OUT
IN
HBM..............................................................................4 kV
MM...............................................................................300V
to GND .............................................. -0.3V to (V
- GND.......................................................................+6.0V
= 100 mA, T
2:
3:
4:
5:
6:
ELECTRICAL
CHARACTERISTICS
Parameters
The minimum V
Reference Feedback Voltage Tolerance applies to adjustable output voltage setting.
V
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
temperature and the thermal resistance from junction to air (i.e. T
allowable power dissipation causes the device to initiate thermal shutdown.
The internal MOSFET switches have an integral diode from the L
to the GND pin. In cases where these diodes are forward-biased, the package power dissipation limits
must be adhered to. Thermal protection is not able to limit the junction temperature for these cases.
The current limit threshold is a cycle-by-cycle peak current limit.
R
is the output voltage setting.
A
= +25°C. Boldface specifications apply over the T
IN
has to meet two conditions: V
T
I
I
IN_SHDN
SHD-HYS
L_SHDN
UVLO
T
Sym
I
V
OUT
V
V
SHD
I
Q
IN
IH
IL
HYS
IN
IN
+ 0.3V)
+ 0.3V)
2.12
Min
-1.0
500
2.7
45
—
—
—
—
—
—
IN
= SHDN = 3.6V, C
IN
±0.1
2.28
Typ
140
150
0.1
≥ 2.7V and V
45
10
A
—
—
—
—
† Notice: Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational sections of this specification is not intended.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
range of -40°C to +85°C.
OUT
Max
2.43
5.5
1.0
60
15
—
—
—
—
—
1
= C
IN
A
X
≥ V
, T
IN
pin to the V
Units
= 4.7 µF, L = 4.7 µH, V
%V
%V
J
OUT
mA
mV
µA
µA
µA
, θ
°C
°C
V
V
IN
IN
JA
+ 0.5V.
). Exceeding the maximum
© 2007 Microchip Technology Inc.
Note 1
Note 1
SHDN = GND
SHDN = V
V
V
V
V
Note 4, Note 5
Note 4, Note 5
IN
IN
IN
IN
IN
= 2.7V to 5.5V
= 2.7V to 5.5V
= 2.7V to 5.5V
Falling
pin, and from the L
Conditions
IN
, I
OUT
OUT
(ADJ) = 1.8V,
= 0 mA
X
pin