FDB-1027 Finisar Corporation, FDB-1027 Datasheet
FDB-1027
Specifications of FDB-1027
Related parts for FDB-1027
FDB-1027 Summary of contents
Page 1
... Rev. 7.00 and SFF-8472 Rev 10.1 portions of SFF-8431 Rev. 1.3 5 Directive 2002/95/EC and Finisar Application Note AN-2038. PRODUCT SELECTION FTLF8528P2BCV © Finisar Corporation November 21, 2007 Rev. B FTLF8528P2BCV APPLICATIONS Tri-Rate 2.125/4.25/8.5 Gb/s Fibre Channel 3 , and compatible with SFF-8432 4 . The product is RoHS compliant and lead-free per ...
Page 2
... Rate Select Pin and 2-wire bus. 6. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. © Finisar Corporation November 21, 2007 Rev. B Name/Description or V EET EER 2 ...
Page 3
... FTLF8528P2BCV Pluggable SFP+ Product Specification – November 2007 Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity (Non-condensing) © Finisar Corporation November 21, 2007 Rev. B Symbol Min Typ Max Vcc -0.5 4.0 T ...
Page 4
... If measured with TJ-free data input signal. In actual application, output TJ will be given by Δ OUT defined in FC-PI-4 , Rev 7.0, Table 13, 800-Mx-SN-y. © Finisar Corporation November 21, 2007 Rev ° 3.0 to 3.6 Volts Symbol Min Typ Vcc 3.0 Icc R 100 in Vin,pp ...
Page 5
... TWDP and stress receiver sensitivity measured with TJ-free data input signal. In actual application, output TJ will be given by Δ OUT IN IN © Finisar Corporation November 21, 2007 Rev ° 3.6 Volts Symbol Min P -9 OUT λ 830 σ OMA 196 OMA ...
Page 6
... Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TÜV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request. © Finisar Corporation November 21, 2007 Rev. B Symbol ...
Page 7
... For more information, please see the SFP MSA documentation Note AN-2030. Please note that evaluation board FDB-1027 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation November 21, 2007 Rev ...
Page 8
... Internally measured transceiver supply voltage Measured TX bias current Measured TX output power Measured RX received average optical power Notes: 1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser. © Finisar Corporation November 21, 2007 Rev. B Symbol Min Typ DD Temperature DD Voltage DD ...
Page 9
... FTLF8528P2BCV Pluggable SFP+ Product Specification – November 2007 X. Mechanical Specifications Finisar’s FTLF8528P2BCV SFP+ transceivers are compatible with the SFF-8432 specification for improved pluggable form factor. © Finisar Corporation November 21, 2007 Rev. B FTLF8528P2BCV 2 Page 9 ...
Page 10
... FTLF8528P2BCV Pluggable SFP+ Product Specification – November 2007 XI. PCB Layout and Bezel Recommendations © Finisar Corporation November 21, 2007 Rev. B Page 10 ...
Page 11
... FTLF8528P2BCV Pluggable SFP+ Product Specification – November 2007 © Finisar Corporation November 21, 2007 Rev. B Page 11 ...
Page 12
... January 27, 2003. 6. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. XIII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com © Finisar Corporation November 21, 2007 Rev. B Page 12 ...