HFBR-0414 Avago Technologies US Inc., HFBR-0414 Datasheet - Page 23

• Manufacturer Part Number: HFBR-0414
• Description: KIT EVAL FIBER OPTIC 20-55MBD
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-0414

• Main Purpose: Interface, Fiber Optics
• Embedded: No
• Utilized Ic / Part: HFBR-1414, HFBR-2416
• Primary Attributes: Ethernet Applications up to 7MBd
• Secondary Attributes: ST Connectors
• Operating Voltage: 1.7 V
• Operating Current: 9 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Description/function: Fiber Optic Kit
• For Use With/related Products: HFBR-14x, HFBR-24x
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 516-2139; HFBR-0414

23
Dynamic Characteristics
C
Notes:
10. The conversion factor for the rise time to bandwidth is 0.41 since the HFBR-24X6 has a second order bandwidth limiting characteristic.
Figure 12. Recommended ac coupled receiver circuit. (See AB 78 and AN 1038 for more information.)
Parameter
Rise/Fall Time
10% to 90%
Pulse Width Distortion
Overshoot
Bandwidth (Electrical)
Bandwidth - Rise
Time Product
1. 2.0 mm from where leads enter case.
2. Typical specifications are for operation at T
3. For 200 m HCS fibers, typical responsivity will be 6 mV/ W. Other parameters will change as well.
4. Pin #2 should be ac coupled to a load 510 ohm. Load capacitance must be less than 5 pF.
5. Measured with a 3 pole Bessel filter with a 75 MHz, -3 dB bandwidth. Recommended receiver filters for various bandwidths are provided in
6. Overdrive is defined at PWD = 2.5 ns.
7. D is the effective diameter of the detector image on the plane of the fiber face. The numerical value is the product of the actual detector diameter
8. Measured with a 10 ns pulse width, 50% duty cycle, at the 50% amplitude point of the waveform.
9. Percent overshoot is defined as:
LOAD
CAUTION: The small junction sizes inherent to the design of these components increase the components’
susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be
taken in handling and assembly of these components to prevent damage and/or degradation which may be
induced by ESD.
Application Bulletin 78.
and the lens magnification.
= 5 pF unless otherwise specified
(
––––––––––
V
PK
V
100%
- V
100%
)
x 100%
30 pF
0.1 µF
-40 C to +85 C; 4.75 V Supply Voltage 5.25 V; R
6
2
3 & 7
Symbol
t
PWD
BW
r
, t
f
10
A
= 25 C and V
R
500
LOADS
POST
Min.
AMP
MIN.
CC
= +5 V dc.
Typ.
3.3
0.4
2
125
0.41
[2]
Max.
6.3
2.5
OUTPUT
LOGIC
+5 V
Units
ns
ns
%
MHz
Hz • s
LOAD
Conditions
P
P
P
t
-3 dB Electrical
= 511 ,
r
R
R
R
= 1.5 ns
= 100 W peak
= 150 W peak
= 5 W peak,
Reference
Figure 15
Note 8,
Figure 14
Note 9
Note 10