CY3276 Cypress Semiconductor Corp, CY3276 Datasheet - Page 13

• Manufacturer Part Number: CY3276
• Description: DEV PROG POWERLINE HIGH EZCOLOR
• Manufacturer: Cypress Semiconductor Corp
• Type: Other Power Managementr

Specifications of CY3276

• Mfg Application Notes: Powerline Comm Brd Design AppNote
• Main Purpose: Interface, Transceiver, Powerline Communication
• Embedded: No
• Utilized Ic / Part: CY8CLED16P01
• Primary Attributes: 2400bps Data Transfer Over High Voltage Power Lines
• Secondary Attributes: User Configurable LEDs
• Board Size: 127 mm x 101.6 mm
• Interface Type: RS-232, Ethernet, I2C, ISSP
• Maximum Operating Temperature: + 40 C
• Operating Supply Voltage: 110 V to 240 V
• Product: Power Management Development Tools
• Dimensions: 127 mm x 101.6 mm
• Silicon Manufacturer: Cypress
• Silicon Core Number: CY8CLED16P01
• Kit Application Type: Communication & Networking
• For Use With/related Products: CY8CLED16P01
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 428-3004

CY3276 Cypress High Voltage Programmable PLC Development Kit Guide, Doc. # 001-55116 Rev. *B
Table 2-4. Headers and Jumpers
CY8CLED16P01-OCD
PWR LED[DS1]
TX LED[DS3]
RX LED[DS2]
BIU LED[DS4]
TP1, TP2, TP3, TP4
S2
J8
LED1-LED4
JP1 (PWR)
JP5 (Reset)
JP4 (I2C-SDA)
JP3 (I2C-SCL)
P40-P46
P47
P01,P02,P04
P07
P21
P23
P25
P26
P17
P15
P16, P12
P30,P31,P32,P33,P34,P35
P36,P37
Headers and Jumpers
This is the Cypress Powerline transceiver chip. It is a 100-pin OCD device
This is a blue LED that glows when the board is powered on
This is a green LED that can be used to indicate when the board is transmit-
ting packets on to the powerline
This is a red LED that can be used to indicate when the signal is received
over the powerline on to the board
This is a yellow LED that can be used to indicate when the transmit fre-
quency band is in use
Grounded test points to facilitate probing/debugging
Reset switch for resetting the CY8CLED16P01-OCD chip
2-pin header for connecting to Vcc and Gnd
Headers connected to general purpose configurable LEDs
Connect this jumper to power an external board. Once this jumper has been
connected, power for the external board can be derived from the V and G
connectors on the I2C header (J15). The CY3276 board can provide a max-
imum of 50mA at 5V to an external board through the V and G pins on the
I2C header(J15).
The jumper is for enabling the reset of the PLC chip through an external
board. Once this jumper has been connected, the external board reset can
be connected to the R pin on the I2C header (J15).
This is a pull up jumper. While communicating through I2C(J15), one side
has to pull up the line. When the jumper is connected, the SDA line will get
pulled high. This needs to be done when the user wants the I2C link to be
pulled up by CY3276 board.
This jumper does not need to be placed if the USB-I2C bridge is used for
communication to the host.
This is a pull up jumper. While communicating through I2C(J15), one side
has to pull up the line. When the jumper is connected, the SCL line will get
pulled high. This needs to be done when the user wants the I2C link to be
pulled up by CY3276 board.
This jumper does not need to be placed if the USB-I2C bridge is used for
communication to the host.
Port pins connected to the LCD card
Free port pin
Port pins connected to LED card used for current sensing feedback for
accurate color control
Free port pin
Port pin connected to the yellow LED for BIU
Port pin connected to the red LED for Rx
Port pin connected to the green LED for Tx
Free port pin
Port pin connect to SCL for I2C
Port pin connect to SDA for I2C
Free port pins
Port pins connected to LED card
Free port pins
Description
PLC Development Board
13
[+] Feedback