HFBR-0416 Avago Technologies US Inc., HFBR-0416 Datasheet - Page 16

• Manufacturer Part Number: HFBR-0416
• Description: KIT EVAL FIBER OPTIC 125-160MBD
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-0416

• Main Purpose: Interface, Fiber Optics
• Embedded: No
• Utilized Ic / Part: HFBR-1416, HFBR-2416
• Primary Attributes: Point to Point Applications up to 155MBd
• Secondary Attributes: ST Connectors
• Kit Contents: Assembled PCB With HFBR-1414 Tx, HFBR-2416 Rx, Application Brief 78 And Other Literature
• Tool / Board Applications: Fiber Optic Transceivers
• Mcu Supported Families: HFBR-0400
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
• Other names: 516-2140; HFBR-0416

16
HFBR-14X4 Output Power Measured out of 1 Meter of Cable
14X2/14X4 Dynamic Characteristics
Parameter
Notes:
1. For I
2. Typical data at T
3. Thermal resistance is measured with the transmitter coupled to a connector assembly and mounted on a printed circuit board.
4. D is measured at the plane of the fiber face and defines a diameter where the optical power density is within 10 dB of the maximum.
5. P
6. When changing W to dBm, the optical power is referenced to 1 mW (1000 W). Optical Power P (dBm) = 10 log P ( W)/1000 W.
7. Pre-bias is recommended if signal rate >10 MBd, see recommended drive circuit in Figure 11.
8. Pins 2, 6, and 7 are welded to the anode header connection to minimize the thermal resistance from junction to ambient. To further reduce the
9. Fiber NA is measured at the end of 2 meters of mode stripped fiber, using the far-field pattern. NA is defined as the sine of the half angle,
Parameter
50/125 m
Fiber Cable
NA = 0.2
62.5/125 m
Fiber Cable
NA = 0.275
100/140 m
Fiber Cable
NA = 0.3
200 m HCS
Fiber Cable
NA = 0.37
Rise Time, Fall Time
(10% to 90%)
Rise Time, Fall Time
(10% to 90%)
Pulse Width Distortion
CAUTION: The small junction sizes inherent to the design of these components increase the components’
susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be
taken in handling and assembly of these components to prevent damage and/or degradation which may be
induced by ESD.
All HFBR-14XX LED transmitters are classified as IEC 825-1 Accessible Emission Limit (AEL)
Class 1 based upon the current proposed draft scheduled to go in to effect on January 1, 1997.
AEL Class 1 LED devices are considered eye safe. Contact your Avago sales representative for
more information.
for HFBR-1412/1414, and with an SMA 905 precision ceramic ferrule for HFBR-1402/1404.
thermal resistance, the anode trace should be made as large as is consistent with good RF circuit design.
determined at 5% of the peak intensity point. When using other manufacturer’s fiber cable, results will vary due to differing NA values and
specification methods.
T
is measured with a large area detector at the end of 1 meter of mode stripped cable, with an ST
FPK
> 100 mA, the time duration should not exceed 2 ns.
A
= 25 C.
Symbol
PT50
PT62
PT100
PT200
Symbol
t
t
PWD
-18.8
-19.8
-17.3
-18.9
-15.0
-16.0
-13.5
-15.1
-9.5
-10.5
-8.0
-9.6
-5.2
-6.2
-3.7
-5.3
r
r
Min.
, t
, t
f
f
Typ.
-15.8
-13.8
-12.0
-10.0
-6.5
-4.5
-3.7
-1.7
Min.
[2]
-11.4
-7.6
-7.0
-2.1
Max.
-13.8
-12.8
-10.8
-10.0
-9.0
-4.5
-3.5
-1.5
+0.8
+1.8
+3.2
+3.8
Typ.
4.0
3.0
0.5
[2]
Unit
dBm
peak
dBm
peak
dBm
peak
dBm
peak
Max.
6.5
T
T
T
T
T
T
T
T
Units
nsec
nsec
nsec
A
A
A
A
A
A
A
A
No Pre-bias
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
= 25 C
®
Conditions
precision ceramic ferrule (MIL-STD-83522/13)
I
I
I
I
I
I
I
I
F
F
F
F
F
F
F
F
= 60 mA dc
= 100 mA dc
= 60 mA dc
= 100 mA dc
= 60 mA dc
= 100 mA dc
= 60 mA dc
= 100 mA dc
Conditions
I
Figure 12
I
100 mA
F
F
= 60 mA
= 10 to
Reference
Notes 5, 6, 9
Reference
Note 7
Note 7,
Figure 11
Figure 11