ATAVRSB201 Atmel, ATAVRSB201 Datasheet
ATAVRSB201
Specifications of ATAVRSB201
Related parts for ATAVRSB201
ATAVRSB201 Summary of contents
Page 1
... Holes for mounting of pin headers or wires. • ISP connector for programming via SPI, and debugging via debugWIRE interface. 1 Introduction The ATAVRSB201-1/SB201-2 kits are evaluation and development kits for the new ® Atmel AVR smart battery device ATmega16HVA. This device is made for battery ...
Page 2
Hardware 2.1 Main area 2.2 Connector and support area AVR455 2 The SB201-1 and SB201-2 have a common PCB and only differ in which components are mounted and the silk screen. They will be commonly referred to as SB201 ...
Page 3
Polarity safety FET 2.2.2 Board ID system 8131A-AVR-10/08 Name Description PV1R Cell1 positive input. PV2R Cell2 positive input. PA0 PA0 pin. PA1 PA1 pin. PB0 PB0 pin. PC0 PC0 pin. Used for 1-wire SW-UART. Includes ESD protection. Table 2-2. ...
Page 4
Single cell mode capacitors 2.2.4 Cell balancing 2.3 Edge connector 3 Connecting batteries to SB201 3.1 2-cell application SB201-2 AVR455 4 The capacitors connected to CF1P/N and CF2P/N allow step up operation of the regulator used for ...
Page 5
SB201-1 4 Programming 5 Debugging 8131A-AVR-10/08 Figure 3-1. Connection of 2-cells in series packs to SB201-2. The SB201-1 for 1-cell in series applications, connect the cell as shown in Figure 3-2: Positive terminal of cell to CELL+ ...
Page 6
... ATmega16HVA has no hardware UART. AVR455 showed a typical current consumption of 160uA for SB201 1-cell application. The schematics for SB201-1 and SB201-2 are provided in the .zip-file that can be downloaded from Atmel AVR Application schematic is provided here. Idle mode [mA] Power save [μA] ...
Page 7
... BAS40L RESET C7 Block Reset 5V from Master to VREG 100n TSM-103-01-T-DH-TR GND R20 10k RESET C10 10n ATMEL Norway GND Vestre Rosten 79 Remove C10 to use debugWire 7075 TILLER NORWAY Date: 17.04.2008 Document number: A08-482/A08-483 TITLE: SB201 monitoring and protection circuit for 1/2-cell Li-ion SB201 ...
Page 8
... AVR455 8 Component placement for SB201-1 and SB201-2 are provided in the .zip-file that can be downloaded from Atmel AVR Application shown here. The BOM is provided in the .zip file that can be downloaded from Application notes. The difference between SB201-1 and SB201-2 is that the SB201-2 provides cell balancing circuitry. Otherwise the SB201-1 has a 0 Ω ...
Page 9
... FCC (except as may be otherwise noted on the board/kit). Atmel supplied this board/kit “AS IS,” without any warranties, with all faults, at the buyer’s and further users’ sole risk ...
Page 10
... BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’ ...