DMP1-4801 Acme Electric/Amveco/Actown, DMP1-4801 Datasheet - Page 2
![PWR SPLY 50W 1.09A 48VDC DINRAIL](/photos/8/84/88465/mfg_dmp1_series_sml.jpg)
DMP1-4801
Manufacturer Part Number
DMP1-4801
Description
PWR SPLY 50W 1.09A 48VDC DINRAIL
Manufacturer
Acme Electric/Amveco/Actown
Series
DMr
Specifications of DMP1-4801
Voltage - Output
48V
Number Of Outputs
1
Power (watts)
50W
Applications
Commercial
Power Supply Type
Switching (Closed Frame)
Voltage - Input
90 ~ 264VAC
Mounting Type
DIN Rail
1st Output
48 VDC @ 1.09A
Size / Dimension
4.02" L x 1.26" W x 3.54" H (102mm x 32mm x 90mm)
Power (watts) - Rated
50W
Operating Temperature
-10°C ~ 50°C
Efficiency
85%
Approvals
CE, UL
Line Regulation
±0.5%
Load Regulation
±1%
Lead Free Status / RoHS Status
Lead free by exemption / RoHS Compliant
3rd Output
-
2nd Output
-
4th Output
-
Cooling and Airflow
Names and Descriptions
Installation Procedure.
Un-Install and Removal Procedure.
Copyright©
notification.
1. Airflow must be upward as shown in figure.
2. Always maintain operation conditions within output power
3. All units are rated for convectional cooling but require that
4. Do not block vent holes because by doing so it may
1.
2.
3.
4.
5.
6.
7.
8.
1. Do not connect wiring until after unit is firmly in place.
2. Locate mounting bracket clip on back of unit. A sliding
3. First slip the top mounting lip of the clip over the top edge
4. From the front side, insert a screwdriver and pull the
5. Apply a downward pressure keeping the top lip firmly
6. Finally, swing the bottom of the unit downward and slide
1. Turn off all AC power and disconnect from its source.
2. With a screwdriver, pull down the release clip and
3. Rotate upward and lift the unit detaching it from the top
and temperature ratings.
there is at least 25mm both above and below unit for
proper airflow.
overheat and damage the unit.
Din Rail rear mounting clip.
spring release clip is built into the lower channel.
of Din Rail as shown in the figure. (The bottom of the unit
should be tilted out about 10°)
release lever all the way downward and hold it.
seated into the top of the Din Rail.
the release clip over the bottom of the Din Rail. Move the
release clip upward to ensure a firm fit with the Din rail.
Disconnect all wiring connections from Power supply.
disengage the bottom channel of the unit from the bottom
edge of the Din Rail. Insert pressure downward on the
unit and tilt the bottom outward.
edge of the Din Rail.
+ Positive output (50W unit has two terminals)
– Negative output (50W unit has two terminals)
DC OK Indicator
ADJ DC output voltage adjustment
N AC mains (Neutral)
L AC mains (Line)
2008,Acme Electric
Safety Ground
Corp.
Acme Electric
DIN Rail Power Supplies, Plastic Single Phase
Corp. reserves the right to make changes in the product at any time, without
INSTALLATION MANUAL
Place top of clip onto
top of Din Rail.
From front side, insert screwdriver and
pull release lever all the way down.
Disconnect
AC Power
Removing
Wiring.
Before
25 mm
25 mm
8
AE Plastic Install Manual.doc 12 August 2008
All Models
Air Flow
Before Installing Wiring.
Disconnect AC Power
Pull release lever down and
then rotate bottom upward.
All Models
25 mm space
above and below
unit is required for
proper airflow.
Rotate bottom down,
then latch lever up.
1, 2
3
4
5, 6, 7