DMP1-12025 Acme Electric/Amveco/Actown, DMP1-12025 Datasheet

DMP1-12025

Manufacturer Part Number

DMP1-12025

Description

PWR SPLY 30W 3A 12VDC DIN-RAIL

Manufacturer

Acme Electric/Amveco/Actown

Series

DMr

Datasheets

1.DMP1-1204.pdf (2 pages)

2.DMP1-1204.pdf (12 pages)

3.DMP1-1204.pdf (2 pages)

Specifications of DMP1-12025

Voltage - Output

12V

Number Of Outputs

Power (watts)

30W

Applications

Commercial

Power Supply Type

Switching (Closed Frame)

Voltage - Input

90 ~ 264VAC

Mounting Type

DIN Rail

1st Output

12 VDC @ 3A

Size / Dimension

4.02" L x 0.9" W x 3.54" H (102mm x 22.8mm x 90mm)

Power (watts) - Rated

30W

Operating Temperature

-10°C ~ 50°C

Efficiency

84%

Approvals

CE, UL

Line Regulation

±0.5%

Load Regulation

±1%

Lead Free Status / RoHS Status

Lead free by exemption / RoHS Compliant

3rd Output

2nd Output

4th Output

Current page: 1 of 2
Download datasheet (979Kb)

WARNING: Never work on the power supply when power is applied. Electric shock and arc risks can cause death, severe personal

injury or substantial property damage. Power source must be off and properly secured before any installation, maintenance or modification

work is completed. Keep away from fire and water. Before installing unit, thoroughly read these instructions.

1. As a reminder, these products are not to be installed in nuclear or medical (patient connect) applications.

2. The units meet the safety requirements of UL508, UL60950-1, IEC/EN60950. They are approved in accordance with EN60950, UL508,

3. These units must always be installed with any national, county or city regulations that apply. Connections to mains supply must be in

4. Sufficient temperature and cooling and space clearances must be ensured as indicated: Operation requires no external cooling but

5. Avoid potential danger of contact with case by ensuring all strands of stranded wire use (if applicable) are fastened in the terminal blocks.

8. Do not introduce any objects into the power supply. The output voltage adjustment potentiometer may only be actuated using

1. Read and follow all instructions before installation as indicated in this manual. This publication is based on information that was

2. DIN Rail Connection; as per local electrical codes and recommended wire sizes.

3. DIN Rail mounted per VDE0160 Please see diagram as noted below.

4. This power supply is designed for professional indoor systems. During operation the power supply must not be accessible. Install and put

5. Do not operate without Protective Earth (PE) connection! To comply with EMC and safety standards (CE mark, approvals) the power

6. Do not cover any ventilation holes. The correct mounting position for optimal cooling performance must be observed. All free space

8. Please ensure that the power supply will be recycled properly at the end of its life. Some components of this power supply may be

WARNING The internal fire safety fuse is not accessible. This fuse is not to be replaced by the user. For continued protection

Safety Instructions

SAFETY ALERT Hazardous voltages and components storing a substantial amount of energy are present in this unit during normal

WARNING Do not open the power supply until at least 5 minutes after it has been disconnected from the mains on all poles.

professionals. Only professionally trained personnel may open the power supply. If you have any questions concerning the

installation or operation of this equipment, please call the number located at the front of this document.

(TUV) EN55022, EN55024, CE MARKING and meet the requirements EMC and the Low Voltage Directive.

compliance with national and city regulations. Power supply and main cables must be sufficiently fused in accordance with local codes.

Follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary, and it is

your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in

compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result by not following all

applicable standards and codes.

application, nor do we assume any responsibility for your product design, installation, or operation.

requires minimum clearances on top, bottom, and sides of units. Refer to installation Cooling and Airflow Requirements below

operating conditions.

an insulated screwdriver.

available at the time it was printed. We reserve the right to make changes to the products and/or publications at any time without notice

and without obligation.

into service by qualified personnel only.

supply must be operated only if PE terminal is connected to the non-fused earth conductor.

requirements and power de-rating as specified at the beginning of this manual must be observed.

against risk of fire, NO REPLACEMENT OF FUSE IS ALLOWED REGARDLESS. If this internal fuse has blown, the power supply has

a serious internal defect, and for safety reasons, must be discarded, or if under warranty, returned.

suitable for recycling, including some that require special disposal.

Installation Instructions

NOTICE: Products are not to be used nor are warranted in aerospace, nuclear, medical patient connect, or lifesafety applications.

SAFETY ALERT

This manual is subject to change without prior notice.

FOR YOUR SAFETY, READ ALL INSTRUCTIONS BEFORE INSTALLATION AND OPERATION.

Improper handling may result in electric shock or serious burns.

WARNING – Avoid Possible Injury or Death

We do not guarantee the products described in this publication are suitable for your particular

DIN Rail Power Supplies, Plastic Single Phase

WARNING – Avoid Personal Injury or Product Damage.

INSTALLATION MANUAL

Units are only to be installed by

Related parts for DMP1-12025

DMP1-12025 Summary of contents

Page 1

SAFETY ALERT FOR YOUR SAFETY, READ ALL INSTRUCTIONS BEFORE INSTALLATION AND OPERATION. NOTICE: Products are not to be used nor are warranted in aerospace, nuclear, medical patient connect, or lifesafety applications. This manual is subject to change without prior notice. ...

Page 2

Cooling and Airflow 1. Airflow must be upward as shown in figure. 2. Always maintain operation conditions within output power and temperature ratings. 3. All units are rated for convectional cooling but require that there is at least 25mm both ...

Related keywords

dmp1-1204
dmp1-12025
DMP1-12025 datasheet
DMP1-12025 data sheet
DMP1-12025 pdf datasheet
DMP1-12025 component
DMP1-12025 part
DMP1-12025 distributor
DMP1-12025 RoHS
DMP1-12025 datasheet download