SCS120PW36 TDK Corporation, SCS120PW36 Datasheet
SCS120PW36
Manufacturer Part Number
SCS120PW36
Description
POWER SUP 36V 3.3A 120W OUTPUT
Manufacturer
TDK Corporation
Series
SCS120PWr
Datasheets
1.SCS120PW48.pdf
(2 pages)
2.SCS120PW48.pdf
(2 pages)
3.SCS120PW48.pdf
(1 pages)
4.SCS120PW48.pdf
(169 pages)
Specifications of SCS120PW36
Voltage - Output
36V
Number Of Outputs
1
Power (watts)
120W
Applications
Commercial
Power Supply Type
Switching (Open Frame)
Voltage - Input
90 ~ 264VAC
Mounting Type
Chassis Mount
1st Output
36 VDC @ 3.3A
Size / Dimension
5" L x 3" W x 1.27" H (127mm x 76.2mm x 32.3mm)
Power (watts) - Rated
118.8W
Operating Temperature
0°C ~ 40°C
Efficiency
85%
Approvals
CE, CSA, EN, UL
Line Regulation
±3%
Load Regulation
±3%
Power Supply Output Type
Fixed
No. Of Outputs
1
Output Voltage
36V
Output Current
3.34A
Power Rating
120W
Input Voltage
90VAC To 264VAC
Supply Voltage Typ
115VAC / 230VAC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
4th Output
-
Other names
285-1968
This manual contains important information regarding the proper installation and operation of the
power supply inside the host equipment.
GENERAL SAFETY INSTRUCTIONS
This power supply is designed for use within other equipment or enclosures. For safe installation and
operation of this product, carefully follow the instructions below:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
FUSING
An internal T3.15A, 250V, time lag, HBC fuse is provided. For continued protection against risk of
fire, replace only with same type and rating as that fitted.
Caution: Changing the fuse is to be performed by qualified service personnel only.
SAFETY AGENCY APPROVALS
The CE Marking, when applied to the product, indicates conformance to the requirements outlined in
the European Union's Low Voltage Directive (72/23/EEC) as amended by the CE Marking directive
(93/68/EEC) in that the product complies with EN60950-1.
Rev. B
Date: 3/02/11
SC120PW Series
Do not install, test or operate this product near water, and do not spill any liquid on it.
Do not operate this product unless it is in a secure position.
This product must be installed in a restricted access location accessible to authorized
competent personnel only.
This product must be reliably earthed and professionally installed in accordance with the
prevailing electrical wiring regulations and safety standards.
After disconnecting the AC source, allow 5 minutes before touching the unit to allow
capacitors within the unit to discharge.
Heat sinks within this power supply are live and must not be touched when the unit is in
operation.
All four 3.5 mm diameter mounting holes at the corners of the unit must be used to secure the
power supply. To conform to EMI specifications, solder pads located around the mounting
holes on the underside of the pcb must make electrical connection with the chassis. Washers
and other mounting hardware must not exceed 6mm in diameter.
A minimum of 4.2mm creepage and 3.8mm clearance must be maintained between the power
supply and the equipment chassis. If the mounting spacer height is less than 8mm, basic
insulation must be provided between the power supply and the equipment chassis.
The output power taken from the power supply must not exceed the rating stated on the power
supply label. For convection cooling, ensure that adequate ventilation is provided to allow air
to circulate naturally.
All servicing, repair and testing of this product must be carried out by competent personnel
who are fully conversant with the hazards of AC line operated equipment and with the
particular dangers associated with switch mode power supplies.
Dangerous voltages are present within the power supply. Power must be disconnected before
servicing.
3055 Del Sol Blvd., San Diego, CA 92154 USA
INSTALLATION MANUAL
SC120PW Model Series
- 1 -
Related parts for SCS120PW36
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Terminals Copper Comp Butt Splice Standard
Manufacturer:
Panduit Corp
Part Number:
Description:
Terminals COPPER SPLICE SHORT BRL 1/0 AWG
Manufacturer:
Panduit Corp
Part Number:
Description:
TDK DC to DC Converters, DC to AC Inverters
Manufacturer:
TDK Corporation
Datasheet:
Part Number:
Description:
TDK DC to DC Converters, DC to AC Inverters
Manufacturer:
TDK Corporation
Datasheet:
SCS120PW36 Summary of contents
Page 1
Del Sol Blvd., San Diego, CA 92154 USA This manual contains important information regarding the proper installation and operation of the power supply inside the host equipment. GENERAL SAFETY INSTRUCTIONS This power supply is designed for use within other ...
Page 2
Del Sol Blvd., San Diego, CA 92154 USA SPECIFICATIONS Marked Input Operating Range Inrush Current Power Factor Correction Output Power Load and Line Regulation Ripple & Noise Over Voltage Protection Over Current Protection Operating Temperature Range Storage Temperature Range ...