SRBC-16F2ALG Bel Fuse Inc, SRBC-16F2ALG Datasheet
SRBC-16F2ALG
Specifications of SRBC-16F2ALG
Related parts for SRBC-16F2ALG
SRBC-16F2ALG Summary of contents
Page 1
... Remote On/Off Description The Bel SRBC-16F2Ax modules are a series of non-isolated dc/dc converters that deliver output current with full load efficiency of 94% at 3.3 Vdc output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 Vdc to 3.63 Vdc over a wide range of input voltage (2.4 Vdc - 5.5 Vdc) ...
Page 2
... Ripple and Noise (rms) Turn on Time Overshoot at Turn on Output Capacitance ESR ≥ 1 mohm ESR ≥ 10 mohm Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output Min Typ Max 2 ...
Page 3
... Max Notes - - - Measured at Vin=5 V, full load - - - - 5% Calculated Per Bell Core SR-332 ( °C) Nominal Notes SRBC-16F2A0; Remote On/Off pin open, Unit on. SRBC-16F2AL; Remote On/Off pin open, Unit on. Sequencing Voltage should be higher than output voltage. Delay from Vinmin to application of voltage on SEQ pin = O ...
Page 4
... Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. = − 1698 trim Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output − 7525 × − ...
Page 5
... Vo=1.2 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output 100.0% 95.0% 90.0% 4.5V 5V 85.0% 5.5V 80.0% 75.0% 70. 95.0% 90.0% 85.0% 3V 80.0% 3 ...
Page 6
... Vdc - 5.5 Vdc Input Thermal Derating Curves Vin=5.0 V, Vo=2 3.3 V Vin=5.0 V, Vo=0.7525 V or 1.2 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output Vin=3.3 V, Vo=0.7525 V or 1.2 V Vin=5.0 V, Vo=1 1.8 V ...
Page 7
... Note: Ripple and noise at 5.0 V input, 0-20MHz BW, 10 uF/16 V tantalum cap and 1uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output Ripple and noise at full load, 1.2 V output Ripple and noise at full load, 1 ...
Page 8
... V output 50% to 100% load step at 1.5 V output Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output 100% to 50% load step at 0.75 V output 100% to 50% load step at 1 ...
Page 9
... Note: Transient response at 5.0 V input, di/dt=2.5 A/uS, with two 150 uF/10 V tantalum capacitors and 1 uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 3.63 Vdc/16 A Output 100% to 50% load step at 1 ...
Page 10
... Remote Sense PAD SIZE: MIN: 0.14"* 0.095" (3.56mm * 2.41mm) MAX: 0.165"* 0.11" (4.19mm * 2.79mm) © 2007 Bel Fuse Inc. Specifications subject to change without notice. 011607 EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. ...