IPM24S0B0S03FA Delta Electronics, IPM24S0B0S03FA Datasheet
IPM24S0B0S03FA
Specifications of IPM24S0B0S03FA
IPM24S0B0S03A
IPM24S0B0S03A
IPM24S0B0S03FA
Q4884455A
Available stocks
Related parts for IPM24S0B0S03FA
IPM24S0B0S03FA Summary of contents
Page 1
... The documentation and background information listed below are relevant to this evaluation procedure: ․ Applicative date sheet for IPM24S Series unit under evaluation. ․ Power Module Evaluation Board Schematic. ․ Power Module Evaluation Board Layout. ․ General Test and Safety Procedures. 1 Delta Electronics, Inc. ...
Page 2
Equipment Required ․ DC Power Supply (Agilent 6574A 0 -60V/0 - 35A or equivalent). ․Oscilloscope (Tektronix TDS 460A or equivalent) 4 Channel 400 MHz, equipped with a x1 scope probe, a ...
Page 3
Connect one lead from the “+” lead of the power supply to the “20A” terminal of the first multimeter DMM1. Then connect one lead from the “Common” of the DMM1 to the “Vin+” pin of the Evaluation Board. Set ...
Page 4
Tests Performed The following tests are performed at room temperature (+25 C). 6.1 Input Characteristics Input Voltage Range. Under-Voltage Locko No Load Input Current 6.2 O utput Characteristics Line Regulation. Load Regulation. Output Regulation . Output Voltage Se t-point ...
Page 5
SW3 for the trim-down or trim-up setting of the Output Voltage. For IPM, if the converter requires a trim up, set SW3 to the Trim-up position. If the converter requires a trim down, set SW3 to ...
Page 6
Initial Power Up 1) Turn the power supply ON, set the current limit on power supply (refer to specification of either converter) and in reaches the desired value. 2) Set the switch SW1 to “ON” position to enable the ...
Page 7
Output Characteristics 8.2.1 Line Regulation Line Regulation Deviation is defined as the change in output voltage caused by varying the in put voltage over ...
Page 8
Output Voltage Set-Point Adjustment Range (Trim) Output Voltage Set-Point Adjustment can be carried out by using an external resistor or external voltage source to increase or decrease the output voltag th e data sheet for the detailed specification). Refer ...
Page 9
Rtrim values versus some commonly used Vout for IPM24S0B0R03 A. Vo Vadj Vadj Vadj Vadj 3.3*(1-10%) Rtrim values versus some commonly used Vout for IPM24S0C0R03 A. Vo Vadj Vadj 8.0*(1-10%) Test T 1) urn on the fan. 2) Adjust the ...
Page 10
Turn-On Transient Time Turn-On Response Time is defined as the time it takes for the output to rise to within 90% of its final value from the time when the converter is enabled. The rise time is deliberately made ...
Page 11
Thermal Characteristic 8.4.1 Efficiency Efficiency is the ratio of total output power to the input power typically measured at full load and nominal input voltage. Test 1) Turn on the fan. 2) Set the enable switch SW1 ...
Page 12
Appendix A- Evaluation Board Schematic 14 ...
Page 13
Appendix B - Evaluation Board Layout (Top View) 15 ...
Page 14
Appendix C - Evaluation Board Layout (Bottom View) CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information ...