AXB070X43Z Lineage Power, AXB070X43Z Datasheet - Page 8

• Manufacturer Part Number: AXB070X43Z
• Description: CONVERTER DC/DC 5-15V 70W SIP
• Manufacturer: Lineage Power
• Series: Austin Lynx™r
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of AXB070X43Z

• Output: 5 ~ 15V
• Number Of Outputs: 1
• Power (watts): 70W
• Mounting Type: Through Hole
• Voltage - Input: 20 ~ 30V
• Package / Case: 10-SIP Module
• 1st Output: 5 ~ 15 VDC @ 4.5A
• Size / Dimension: 2.00" L x 0.32" W x 0.50" H (50.8mm x 8.1mm x 12.7mm)
• Power (watts) - Rated: 70W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 97%
• Approvals: CSA, EN, UL, VDE
• Product: Non-Isolated / POL
• Output Power: 70 W
• Input Voltage Range: 20 V to 30 V
• Output Voltage (channel 1): 5 V to 15 V
• Package / Case Size: SIP
• Output Type: Non-Isolated
• Output Voltage: 5 V to 15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 555-1153; CC109121480

Test Configurations
Figure 25. Input Reflected Ripple Current Test
Setup.
Figure 26. Output Ripple and Noise Test Setup.
Figure 27. Output Voltage and Efficiency Test Setup.
NOTE: All voltage measurements to be taken at the module
Data Sheet
October 2, 2009
LINEAGE
V
GND
O
(+)
Efficiency
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
TO OSCILLOSCOPE
NOTE: Measure input reflected ripple current with a simulated
R
R
NOTE: All voltage measurements to be taken at the module
distribution
distribution
0.01uF
source inductance (L
possible battery impedance. Measure current as shown
above.
POWER
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
COPPER STRIP
R
R
contact
contact
η =
0.1uF
@ 20°C 100kHz
E.S.R.<0.1Ω
C
S
GROUND PLANE
10uF
L
220μF
V
1μH
TEST
IN
V
V
V
COM
IN
IN
O
TEST
(+)
. I
. I
) of 1μH. Capacitor C
O
IN
SCOPE
COM
V
O
V
150μF
C
x 100 %
O
Min
IN
RESISTIVE
LOAD
CURRENT PROBE
R
R
contact
contact
S
offsets
V
COM
IN
(+)
R
R
distribution
distribution
R
LOAD
Austin Lynx
Safety Considerations
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950, CSA C22.2 No. 60950-00, EN60950
(VDE 0850) (IEC60950, 3
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power
module has extra-low voltage (ELV) outputs when all
inputs are ELV.
20– 30Vdc input; 5.0 – 15.0Vdc Output; 70W
TM
24V: Non-isolated Power Modules:
rd
edition) Licensed.
8