LTM4607EV#PBF Linear Technology, LTM4607EV#PBF Datasheet - Page 7

• Manufacturer Part Number: LTM4607EV#PBF
• Description: IC BUCK/BOOST SYNC ADJ 5A 141LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4607EV#PBF

• Design Resources: LTM4607 Spice Model
• Output: 0.8 ~ 24 V
• Number Of Outputs: 1
• Power (watts): 120W
• Mounting Type: Surface Mount
• Voltage - Input: 4.5 ~ 36 V
• Package / Case: 141-LGA
• 1st Output: 0.8 ~ 24 VDC @ 5A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 120W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 98%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

PIN FUNCTIONS
V
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between V
and PGND pins.
V
between these pins and PGND pins. Recommend placing
output decoupling capacitance directly between these pins
and PGND pins.
PGND (Bank 6): Power Ground Pins for Both Input and
Output Returns.
SW1, SW2 (Bank 4, Bank 2): Switch Nodes. The power
inductor is connected between SW1 and SW2.
R
tor is connected from this pin to PGND.
SENSE
Reverse Current Detect Comparators.
SENSE
Reverse Current Detect Comparators.
EXTV
5.7V, an internal switch connects this pin to INTV
shuts down the internal regulator so that the controller and
gate drive power is drawn from EXTV
7V at this pin and ensure that EXTV
INTV
is for additional decoupling of the 6V internal regulator.
PLLIN (Pin B9): External Clock Synchronization Input
to the Phase Detector. This pin is internally terminated
to SGND with a 50k resistor. The phase-locked loop will
force the rising bottom gate signal of the controller to be
synchronized with the rising edge of PLLIN signal.
PLLFLTR (Pin B8): The lowpass filter of the phase-locked
loop is tied to this pin. This pin can also be used to set the
frequency of the internal oscillator with an AC or DC volt-
age. See the Applications Information section for details.
SS (Pin A6): Soft-Start Pin. Soft-start reduces the input
surge current from the power source by gradually increas-
ing the controller’s current limit.
IN
OUT
SENSE
(Bank 1): Power Input Pins. Apply input voltage be-
CC
CC
(Bank 5): Power Output Pins. Apply output load
+
–
(Bank 3): Sensing Resistor Pin. The sensing resis-
(Pin F6): External V
(Pin F5): Internal 6V Regulator Output. This pin
(Pin A4): Positive Input to the Current Sense and
(Pin A5): Negative Input to the Current Sense and
CC
Input. When EXTV
CC
CC
< V
. Do not exceed
IN
.
CC
exceeds
IN
CC
pins
and
STBYMD (Pin A10): LDO Control Pin. Determines whether
the internal LDO remains active when the controller is
shut down. See the Operations section for details. If the
STBYMD pin is pulled to ground, the SS pin is internally
pulled to ground to disable start-up and thereby provid-
ing a single control pin for turning off the controller. An
internal decoupling capacitor is tied to this pin.
V
Internally, this pin is connected to V
sion resistor. Different output voltages can be programmed
with an additional resistor between V
See the Applications Information section.
FCB (Pin A9): Forced Continuous Control Input. The
voltage applied to this pin sets the operating mode of the
module. When the applied voltage is less than 0.8V, the
forced continuous current mode is active. When this pin
is allowed to float, the Burst Mode operation is active in
boost operation and the skip cycle mode is active in buck
operation. When the pin is tied to INTV
frequency discontinuous current mode is active in buck or
boost operation. See the Applications Information section.
SGND (Pin A7): Signal Ground Pin. This pin connects to
PGND at output capacitor point.
COMP (Pin B7): Current Control Threshold and Error
Amplifier Compensation Point. The current comparator
threshold increases with this control voltage. The voltage
ranges from 0V to 2.4V.
PGOOD (Pin B5): Output Voltage Power Good Indicator.
Open drain logic output that is pulled to ground when the
output voltage is not within ±10% of the regulation point,
after a 25μs power bad mask timer expires.
RUN (Pin A8): Run Control Pin. A voltage below 1.6V will
turn off the module. There is a 100k resistor between the
RUN pin and SGND in the module. Do not apply more than
6V to this pin. See the Applications Information section.
FB
(Pin B6): The Negative Input of the Error Amplifier.
OUT
FB
LTM4607
with a 100k preci-
CC
and SGND pins.
, the constant
4607fb
7