FW300H1 Lineage Power, FW300H1 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/3/387/lineage_power_sml.jpg)
FW300H1
Manufacturer Part Number
FW300H1
Description
CONVERTER DC/DC 24V 300W OUT
Manufacturer
Lineage Power
Series
FW300r
Type
Isolated with Remote On/Offr
Datasheet
1.FW250H1.pdf
(20 pages)
Specifications of FW300H1
Output
24V
Number Of Outputs
1
Power (watts)
300W
Mounting Type
Through Hole
Voltage - Input
36 ~ 75V
Package / Case
Module
1st Output
24 VDC @ 12.5A
Size / Dimension
4.60" L x 2.40" W x 0.53" H (116.8mm x 61mm x 13.5mm)
Power (watts) - Rated
300W
Operating Temperature
-40°C ~ 100°C
Efficiency
89%
Approvals
CE, CSA, UL, VDE
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
3rd Output
-
2nd Output
-
4th Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FW300H1
Manufacturer:
LUCENT
Quantity:
27
Part Number:
FW300H1
Manufacturer:
SANKEN
Quantity:
20 000
Part Number:
FW300H1
Quantity:
55
Part Number:
FW300H1
Quantity:
55
FW250H1 and FW300H1 Power Modules; dc-dc Converters:
36 Vdc to 75 Vdc Input, 24 Vdc Output; 250 W to 300 W
12
12
Feature Descriptions
Output Current Monitor
The CURRENT MON pin provides a dc voltage propor-
tional to the dc output current of the module given in
the Feature Specifications table. For example, on the
FW250H1, the V/A ratio is set at 250 mV/A
70 C case. At a full load current of 12.5 A, the voltage
on the CURRENT MON pin is 3.13 V. The current mon-
itor signal is referenced to the SENSE(–) pin on the
secondary and is supplied from a source impedance of
approximately 2 k . It is recommended that the CUR-
RENT MON pin be left open when not in use, although
no damage will result if the CURRENT MON pin is
shorted to secondary ground. Directly driving the CUR-
RENT MON pin with an external source will detrimen-
tally affect operation of the module and should be
avoided.
Synchronization
Any module can be synchronized to any other module
or to an external clock using the SYNC IN or SYNC
OUT pins. The modules are not designed to operate in
a master/slave configuration; that is, if one module fails,
the other modules will continue to operate.
SYNC IN Pin
This pin can be connected either to an external clock or
directly to the SYNC OUT pin of another FW250x or
FW300x module.
If an external clock signal is applied to the SYNC IN
pin, the signal must be a 500 kHz (±50 kHz) square
wave with a 4 Vp-p amplitude. Operation outside this
frequency band will detrimentally affect the perfor-
mance of the module and must be avoided.
If the SYNC IN pin is connected to the SYNC OUT pin
of another module, the connection should be as direct
as possible, and the V
shorted together.
Unused SYNC IN pins should be tied to V
SYNC IN pin is unused, the module will operate from
its own internal clock.
I
(–) pins of the modules must be
(continued)
I
(–). If the
10% @
SYNC OUT Pin
This pin contains a clock signal referenced to the V
pin. The frequency of this signal will equal either the
module’s internal clock frequency or the frequency estab-
lished by an external clock applied to the SYNC IN pin.
When synchronizing several modules together, the
modules can be connected in a daisy-chain fashion
where the SYNC OUT pin of one module is connected
to the SYNC IN pin of another module. Each module in
the chain will synchronize to the frequency of the first
module in the chain.
To avoid loading effects, ensure that the SYNC OUT
pin of any one module is connected to the SYNC IN pin
of only one module. Any number of modules can be
synchronized in this daisy-chain fashion.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with an overtemperature shutdown circuit.
The shutdown circuit will not engage unless the unit is
operated above the maximum case temperature.
Recovery from overtemperature shutdown is
accomplished by cycling the dc input power off for at
least 1.0 second or toggling the primary referenced on/
off signal for at least 1.0 second.
Forced Load Sharing (Parallel Operation)
For either redundant operation or additional power
requirements, the power modules can be configured for
parallel operation with forced load sharing (see
Figure 19). For a typical redundant configuration,
Schottky diodes or an equivalent should be used to
protect against short-circuit conditions. Because of the
remote sense, the forward-voltage drops across the
Schottky diodes do not affect the set point of the
voltage applied to the load. For additional power
requirements, where multiple units are used to develop
combined power in excess of the rated maximum, the
Schottky diodes are not needed.
Good layout techniques should be observed for noise
immunity. To implement forced load sharing, the follow-
ing connections must be made:
Tyco Electronics Corp.
September 2001
Data Sheet
I
(–)