FW250H1 Lineage Power, FW250H1 Datasheet - Page 11

• Manufacturer Part Number: FW250H1
• Description: CONVERTER DC/DC 24V 250W OUT
• Manufacturer: Lineage Power
• Series: FW250r
• Type: Isolated with Remote On/Offr

Specifications of FW250H1

• Output: 24V
• Number Of Outputs: 1
• Power (watts): 250W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 75V
• Package / Case: Module
• 1st Output: 24 VDC @ 10.4A
• Size / Dimension: 4.60" L x 2.40" W x 0.53" H (116.8mm x 61mm x 13.5mm)
• Power (watts) - Rated: 250W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 89%
• Approvals: CE, CSA, UL, VDE
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -

Feature Descriptions
Output Voltage Set-Point Adjustment
(Trim)
Output voltage trim allows the user to increase or
decrease the output voltage set point of a module. This
is accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(–) pins. The trim resistor should be positioned
close to the module.
If not using the trim feature, leave the TRIM pin open.
With an external resistor between the TRIM and
SENSE(–) pins (R
(V
tion determines the required external-resistor value to
obtain a percentage output voltage change of %.
With an external resistor connected between the TRIM
and SENSE(+) pins (R
point (V
The following equation determines the required exter-
nal-resistor value to obtain a percentage output voltage
change of %.
The voltage between the V
must not exceed the minimum value of the output over-
voltage protection as indicated in the Feature Specifi-
cations table. This limit includes any increase in voltage
due to remote-sense compensation and output voltage
set-point adjustment (trim). See Figure 16.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. Consult the factory if you
need to increase the output voltage more than the
above limitation.
The amount of power delivered by the moudle is
defined as the voltage at the output terminals multiplied
by the output current. When using remote sense and
trim, the output voltage of the module can be
increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
R
adj-up
O, adj
R
adj-down
) decreases (see Figure 17). The following equa-
=
O, adj
Tyco Electronics Corp.
Data Sheet
September 2001
------------------------------------------------------------------------ - 205
V
) increases (see Figure 18).
=
O, nom
205
--------- - 2.255
adj-down
%
1
1.225 %
–
+
adj-up
--------- -
100
), the output voltage set point
%
O
), the output voltage set
(+) and V
–
(continued)
1.225
k
O
(–) terminals
–
2.255
FW250H1 and FW300H1 Power Modules; dc-dc Converters:
k
36 Vdc to 75 Vdc Input, 24 Vdc Output; 250 W to 300 W
Figure 17. Circuit Configuration to Decrease
Figure 18. Circuit Configuration to Increase
Output Overvoltage Protection
The output voltage is monitored at the V
pins of the module. If the voltage at these pins exceeds
the value indicated in the Feature Specifications table,
the module will shut down and latch off. Recovery from
latched shutdown is accomplished by cycling the dc
input power off for at least 1.0 second or toggling the
primary referenced on/off signal for at least 1.0 second.
V
ON/OFF
CASE
V
V
ON/OFF
CASE
V
I
I
I
I
(+)
(–)
(+)
(–)
Output Voltage
Output Voltage
SENSE (+)
SENSE (–)
SENSE (+)
SENSE (–)
V
V
TRIM
V
TRIM
V
O
O
O
O
(+)
(+)
(–)
(–)
R
R
adj-down
adj-up
O
(+) and V
R
R
LOAD
LOAD
O
8-748
8-715
(–)
11