NMR102C Murata Power Solutions Inc, NMR102C Datasheet - Page 3
![CONV DC/DC 1W 5VIN 15V SIP SGL](/photos/8/65/86529/nmr102c_sml.jpg)
NMR102C
Manufacturer Part Number
NMR102C
Description
CONV DC/DC 1W 5VIN 15V SIP SGL
Manufacturer
Murata Power Solutions Inc
Series
NMRr
Type
Isolatedr
Datasheet
1.NMR106C.pdf
(5 pages)
Specifications of NMR102C
Number Of Outputs
1
Output
15V
Power (watts)
1W
Mounting Type
Through Hole
Voltage - Input
4.5 ~ 5.5V
Package / Case
7-SIP Module (4 Leads)
1st Output
15 VDC @ 67mA
Size / Dimension
0.77" L x 0.24" W x 0.39" H (19.6mm x 6.1mm x 9.9mm)
Power (watts) - Rated
1W
Operating Temperature
-40°C ~ 85°C
Efficiency
79%
Approvals
UL
Output Power
1 W
Input Voltage Range
4.5 V to 5.5 V
Input Voltage (nominal)
5 V
Output Voltage (channel 1)
15 V
Output Current (channel 1)
67 mA
Isolation Voltage
1 KV
Package / Case Size
SIP-7
Output Voltage
15 V
Product
Isolated
Input Voltage
5V
Screening Level
Industrial
Product Height (mm)
10mm
Mounting Style
Through Hole
Pin Count
4
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1568-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NMR102C
Manufacturer:
VICOR
Quantity:
12 000
APPLICATION NOTES
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test confi guration.
Differential Mode Noise Test Schematic
C1
C2
C3
R1
R2
T1
RLOAD
Measured values are multiplied by 10 to obtain the specifi ed values.
NMR100C
NMR101C
NMR102C
NMR106C
NMR107C
NMR108C
1μF X7R m ultilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon fi lm, ±1% tolerance
50Ω BNC termination
3T of the coax cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Start-up time
2301
5570
8289
4770
4850
783
μs
SUPPLY
DC/DC Converter
Input
+
-
Output
NMR112C
NMR113C
NMR114C
NMR118C
NMR119C
NMR120C
+
-
C1 C2 C3
R LOAD
Start-up time
1908
6620
5335
6370
744
671
R1
μs
T1
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
R2
Isolated 1W Single Output DC/DC Converters
OSCILLOSCOPE
Y INPUT
Typical Start-Up Wave Form
2010-07-08 KDC_NMR.D01 Page 3 of 5
NMR Series