CT6H203 Vishay, CT6H203 Datasheet - Page 3

• Manufacturer Part Number: CT6H203
• Description: POT 20K OHM 6MM CERMET HORZ
• Manufacturer: Vishay
• Series: CT6r

Specifications of CT6H203

• Resistance (ohms): 20K
• Power (watts): 0.5W, 1/2W
• Taper: Linear
• Tolerance: ±10%
• Temperature Coefficient: ±100ppm/°C
• Number Of Turns: Single
• Adjustment Type: Side Adjustment
• Mounting Type: Through Hole
• Resistive Material: Cermet
• Package / Case: Square - 0.276" L x 0.276" W x 0.323" H (7.00mm x 7.00mm x 8.20mm)
• Resistance In Ohms: 20.0K
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: Q1946237B

Nominal resistance range
Resistance tolerance
Power ratings
Resistance law
Maximum input voltage
Maximum wiper current
Effective electrical angle
End resistance
C.R.V.
Operating temp. range
Temp. coefficient
Insulation resistance
Dielectric strength
Net weight
Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
Nominal resistance values ( )
ELECTRICAL CHARACTERISTICS
MAXIMUM INPUT RATINGS
A
A
100 k
200 k
500 k
10 k
20 k
50 k
100
200
500
1 M
2 M
1 k
2 k
5 k
10
20
50
Approx. 0.51 g (CT-6P, W, R, V, EP, EW, ER, EV)
Approx. 0.65 g (CT-6S, X, H, N, ES, EX, EH, EN)
Approx. 0.92 g (CT-6F, EF)
DC200 V or power rating, whichever is smaller
100 mA or power rating, whichever is smaller
50
10
1 % or 2 , whichever is greater
1 % or 3 , whichever is greater
1000 M minimum (DC500 V)
0.5 W (70 °C) 0 W (120 °C)
~ 2 M : 100 10
~ 20
Resistance code
AC900 V, 60 s
Linear law (B)
220 ° (1 turn)
10
: 250 10
55 ~ 120 °C
100
200
500
101
201
501
102
202
502
103
203
503
104
204
504
105
205
10 %
~ 2 M
-6
-6
/°C maximum
/°C maximum
Maximum input voltage (V)
1.00
2.00
5.00
7.07
10.0
15.8
22.4
31.6
50.0
70.7
100
158
200
200
200
200
200
Mechanical angle
Operating torque
Stop strength
Rotational life
Teminal strength
Thrust to rotor
Solderability
Thermal shock
Humidity
Shock
Vibration
Load life
Low temp. operation
High temp. exposure
Immersion seal
Soldering heat
Test item
MECHANICAL CHARACTERISTICS
ENVIRONMENTAL CHARACTERISTICS
Sn-Pb : 350 °C, 3 s
Sn
Flow : 260
Manual soldering : 380 10 °C, 3 ~ 4 s
10 ~ 2000 Hz, 3 directions, 12 times each
10 ~ 65 °C (Relative humidity 80 ~ 98 %),
Maximum wiper current (mA)
6 directions for 3 times each
65 ~ 125 °C (0.5 h), 5 cycles
maximum
COPAL ELECTRONICS
70 °C, 0.5 W, 1000 h
Amplitude 1.52 mm or
Acceleration 196 m/s
Test conditions
981 m/s
10 cycles, 240 h
120 °C, 250 h
85 °C, 60 s
3 °C, 5 ~ 6 s, two times
55 °C, 2 h
70.7
50.0
31.6
22.4
15.8
10.0
7.07
5.00
3.16
2.00
1.00
0.40
0.20
0.10
100
100
100
200 cycles [ R/R ≦ (2
Sn (Lead-free) : 245 3 °C, 2 ~ 3 s
CERMET TRIMMERS
2
, 6 ms
50 mN·m {510 gf·cm} minimum
2 ~ 20 mN·m {20 ~ 204 gf·cm}
10 N {1.02 kgf} minimum
10 N {1.02 kgf} minimum
2
Sn-Pb : 235 °C, 2 s
,
(Tensile strength)
260 ° (1 turn)
S.S. : Setting stability
R/R : Change in total resistance
No leaks (No continuous bubbles)
The products indi-
cated by A mark are
manufactured upon
receipt of order basis.
{ } : Reference only
Specifications
[ R/R ≦ 1 %]
[ R/R ≦ 2 %]
[ R/R ≦ 1 %]
[ R/R ≦ 3 %]
[ R/R ≦ 2 %]
[ R/R ≦ 3 %]
[ R/R ≦ 1 %]
[S.S. ≦ 1 %]
[S.S. ≦ 1 %]
[S.S. ≦ 1 %]
[S.S. ≦ 2 %]
[S.S. ≦ 2 %]
CT-6
3 %)]
2004
Oct,